manualshive.com logo in svg

Megger 651403, Инструкция по эксплуатации

Поделиться
Скачать
Megger 651403 Скачать руководство пользователя страница 5

 

 

AVTM6514J Rev. A (03/2003) 

1 

SECTION 1 

Introduction 

RECEIVING INSTRUCTIONS 

Check the equipment received against the packing list to ensure that all materials are 

present. Notify Megger of any shortage. Telephone (610) 676-8500. 
Examine the instrument for possible damage received in transit. If any damage is 

discovered, file a claim with the carrier at once and notify Megger or its nearest 
authorized sales representative, giving a detailed description of the damage. 
This instrument has been thoroughly tested and inspected to meet rigid specifications 
before being shipped. It is ready for use when set up as indicated in this manual. 

GENERAL INFORMATION 

This instruction manual describes the operation and maintenance of Impulse 

Generators having Catalog No. 651403 and 651404. Catalog No. 651403 is the 120 V, 
50/60 Hz, 300 VA model, and Catalog No. 651404 is the 240 V, 50/60 Hz, 300 VA 

model. 
The Impulse Generator produces periodic pulses up to 15 kV for locating faults in 

cables by the high-voltage, impulse-tracing method. No larger than a medium-sized 
suitcase and weighing only 41 pounds, the Impulse Generator is contained in a 

fiberglass carrying case that is rugged and durable to withstand transportation from site 
to site. See Figure 1. 
The Impulse Generator uses low-voltage storage capacitors on the primary side of a 
pulse transformer. Every six seconds, a solid-state switch discharges the capacitors into 

the pulse transformer, which steps the voltage up to the required level. The resultant 
output is a high-voltage impulse with a steep front and an exponentially decaying "tail" 

— an ideal waveform for cable fault location. The waveform travels along the cable 
until it reaches the fault, where a sparkover occurs. High-voltage sparkover causes a 

significant current to flow, and the fault is located by detecting this current or the noise 
made by the sparkover. 
An ammeter on the Impulse Generator displays peak fault current in percentage of the 
available output. When the meter indicates a cable fault, its location is pinpointed by 

tracing the fault current with a detector carried along the cable path. Two such detectors 
are available from Megger: 

Содержание 651403









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды