manualshive.com logo in svg

Megger 651403, Инструкция по эксплуатации

Поделиться
Скачать
Megger 651403 Скачать руководство пользователя страница 27

 

 

AVTM6514J Rev. A (03/2003) 

23 

Section 8 

Service 

MAINTENANCE 

The Impulse Generator is constructed to withstand use normally encountered in field 

testing for public utilities and industrial plants. To maintain this equipment in proper 
condition, a planned program of routine maintenance should be carried out every six 

months. 
 

F

 

WARNING 

This is a high-voltage system which can produce and contain 
dangerous voltages. Any service or repair of this equipment 

should be performed only by qualified persons who are aware 

of high-voltage hazards and the necessary precautions routinely 
taken to prevent injury. 

Before any inspection, service, or repair, the system must be completely disconnected 
from the power supply and from any cable under test. Set the OUTPUT KILOVOLTS 

switch to ZERO START. The OUTPUT KILOVOLTS switch must remain set to 
ZERO START for at least 15 minutes before access is gained to the interior of the 

chassis.  

F

 

WARNING 

When it is necessary to touch the terminals of any of the 

capacitors, all terminals of the capacitor should be grounded 
using a safety grounding stick and then bonded together with 

safety ground jumpers, before any connections are removed 
from the capacitor. 

If company policy requires that a defect report be provided to those performing 

maintenance, this report should be consulted and the items noted on the report 
investigated at the appropriate point in the maintenance procedure. 

Maintenance Procedure 

1.  Examine all cables to locate any loose or damaged terminals. 

2.  Inspect and clean the outer jacket of the HV OUTPUT cable; check for breaks in 

this jacket. As a temporary repair, and only if the shield is intact, apply at least four 

layers of vinyl tape over any such damage. Replace the damaged output cable as 
soon as practical. 

Содержание 651403









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды