MegaSquirt DBWX2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

MegaSquirt DBWX2 Скачать руководство пользователя страница 4

I/O and pinout

The controller has six 0-5V analog inputs for pedal and drive by wire throttle body position
sensors. These inputs are protected from short to ground and +12V.

The controller has four 5V reference voltage outputs to be used as pedal and dbw position
sensor reference voltage. These outputs are protected from short to ground.

Two full bridge outputs to be used to drive the brushed DC motors in DBW throttlebodies. These
outputs are protected from short to ground and +12V.

Gray connector

1:DBW1
motor -

2: DBW1
motor +

3: DBW1 ref
5v out

4: DBW2 ref
5v out

5: DBW2
motor -

6: DBW2
motor +

7: DBW1 ref
gnd

8: DBW1
main sense
in

9: DBW1
secondary
sense in

10: DBW2 ref
gnd

11: DBW2
main sense

12: DBW2
secondary
sense

Black connector

1: +12V IN

2: +12V in

3: Pedal main
5v out

4: Pedal main
sense in

5: CAN-L

6: CAN-H

7: GND IN

8: GND IN

9: Pedal
secondary 5v
out

10: Pedal
secondary
sense in

11: Pedal
reference
gnd

12: DBW
fault output

3

«
...
2
3
4
5
6
...
»

Содержание DBWX2

























Отзывы:

Нет отзывов