ALARM FEATURE “
III
” PRORAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch
6
times and hold it on the
6
th
push until three chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature
‘III’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
The vehicle has an aftermarket Turbo timer installed: The system
can be armed with the engine running and:
1
Vehicles without
Turbo (The system
cannot be armed
with the engine
running)
The shock sensor
will be bypassed as
long as the engine
running.
The shock sensor
will be bypassed for
one minute
The shock sensor
will be bypassed for
three minutes
2
H1/4 Brown Wire =
Constant siren
output for six-tone
siren
H1/4 Brown Wire =
5-second pulse siren
output for single-tone
siren
H1/4 Brown Wire =
Random pulse siren
output
H1/4 Brown Wire =
Pulse output
3
H7/7 Red / White
Wire Channel 3 =
1 second pulse
output for trunk
release.
H7/7 Red / White
Wire Channel 3 =
Latch output
H7/7 Red / White
Wire Channel 3 =
Timer controlled
output
4
H7/10 Purple /
Black Wire Channel
4 =
Momentary output
H7/10 Purple / Black
Wire Channel 4 =
Latched output
H7/10 Purple / Black
Wire Channel 4 =
Latched output and
reset with ignition
“ON”
H7/10 Purple / Black
Wire Channel 4 =
Timer programming
(set to any interval
between 1 second
and 2 minutes.)
Exit:
Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Channel 3 (4) Timer Control Output Programming
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch
6
times and hold it on the
6
th
push until
three
chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature
‘III”
programming mode.
3-a. Press and release the transmitter
button 3 times, [3] LED flash, [3] siren/horn chirp to indicate
you are in features “Channel 3 Timer Programming mode”.
3-b. Press and release the transmitter
button 4 times, [4] LED flash, [4] siren/horn chirp to indicate
you are in features “Channel 4 Timer Programming mode”.
4. Press and hold the valet switch, the timer will immediately start.
5. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation.
(Set to any interval between 1 second and 2 minutes)
Note 1:
If your built-in timer controls window/sunroof closure in your car, DO NOT change the timer
setting! This requires installer-only programming. Changing the value will adversely effect
operation and may cause damage.
Note 2:
Momentary output:
The momentary output selection will output a negative signal from the Channel 4
output immediately when the Channel 4 button is pressed and will continue until the button is released.
Latched output
: The latched output selection will output a negative signal as soon as the Channel 3 (4)
button is pressed and will continue until the button is pressed again.
Latched output / reset with ignition:
The latched / reset with ignition output selection operates just like
the latched output but will reset or stop when the ignition is turned on.
MEGA 2550 INSTALL
9
