ALARM FEATURE “
IV
” PRORAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until four chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature
‘IV’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulses
1
Exit the programming mode. (3 long chirps to confirm this exit.)
2
Override Without Password Pin Code
/
Press & hold
button for 4 seconds to
delete the Password pin code
Override With Password Pin Code
/
Password pin code programming
3
“TEST” Mode for Zone 2 Hood & Zone 3
Door Pin Switch
“TEST” Mode for Zone 4 / the Optional
Sensor connected to 4-pin plug.
Exit:
Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Password Pin Code Setup:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature
‘IV’
programming mode.
3. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate you are
in features “Password Pin Code Programming mode”.
4. Within 15 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet switch
from 1 – 9 times.
5. Within 15 seconds of the last entered 10ths digit, turn the Ignition switch to the “ON” position.
6. Within 15 seconds, enter your chosen second 10ths digit by pressing and releasing the valet switch
from 1 – 9 times.
7. Finish by turning the ignition switch to the “OFF” position.
If the new password code were accepted, the unit would report the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause, and then the second digit code. The
unit will report the new code three times with a one-second pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more than 5 seconds
during of the above steps, the unit will go back to the last successfully stored code. [3] long chirps will
confirm password programming exit.
Delete Password Pin Code (Override Without Password Pin Code):
(Factory default setting)
1. Turn the Ignition switch ‘ON/OFF’ 3 times and stay in the OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch.
3. Within 15 seconds, press and hold the transmitter
button for 4 seconds. One long chirp to confirm
that the Password Pin Code has been deleted.
Example: To program the Password Code 92, you would:
1. Turn the Ignition switch ‘ON/OFF’ 3 times and stay in the OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature
‘IV’
programming mode.
3. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate you are
in feature “Password pin code programming mode”.
4. Within 15 seconds, press and release the valet switch 9 times.
5. Within 15 seconds of the last entered 10ths digit, turn the Ignition Switch to “ON” position.
6. Within 15 seconds press and release the valet switch 2 times.
7. Turn the Ignition Switch to the “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in the memory.
MEGA 2550 INSTALL
10
