Mega MULTITRUCK 400 - 600 Скачать руководство пользователя | Manualshive

Страница: 42 / 46

background image

8-Pre-heating

When the ignition is on, the display managed the pre-heating system and the
pre-heating indicator light.

When the ignition is off, the pre-heating system and the indicator light are switching off by the
display.

The pre-heating time depends of the engine temperature, drive by a CTN sensor.

If the CTN sensor is unplugged, 0°c is taken to estimate the pre-heating time.

9-Engine Stop

When the ignition is switched off, the engine stop solenoid is fed for 8 seconds by a timing relay.

«
...
40
41
42
43
44
...
»

Содержание MULTITRUCK 400 - 600















































Отзывы:

Нет отзывов

Похожие инструкции для MULTITRUCK 400 - 600

Бренд: PIAGGIO Страницы: 39

Бренд: Denver Страницы: 23

Бренд: Speedlion Страницы: 9

Бренд: Jetson Страницы: 3

Бренд: SXT Страницы: 22

Бренд: Razor Страницы: 15

Бренд: WHILL Страницы: 114

Бренд: VRLA Страницы: 20

Бренд: Hudora Страницы: 12

Бренд: Hudora Страницы: 24

Бренд: Baotian Страницы: 100

Бренд: Roma Medical Страницы: 20

Бренд: VOI Страницы: 11

Бренд: Scootmobiel Страницы: 13

Бренд: besrey Страницы: 10

Бренд: Jiangsu Niu Electric Technology Страницы: 101

Бренд: Jetson Страницы: 19

Бренд: Jetson Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды