Meec tools 249450, Руководство по эксплуатации

Страница: 39 / 48

39 І 48
2. Device Description
(Abb.1-4)
1. Saw bench
2. Bench insert
3. Saw blade
4. Saw blade guard
5. Suction hose
6. Riving knife
7. Transverse stop
8. Bench extension
9. Push stick
10. Underframe
11. On/Off switch
12. Hand wheel
13. Locking handle
14. Guide rail
15. Rip fence
16. Legs
16a Rubber feet
16b Support frame
17. Long crossbar
18. Short centre brace
19. Hexagon head bolt
20. Hexagon head nut
21. Saw blade spanner
21a Spring ring
21b Washer
22. Support strut
3. Unpacking
• Open the packaging and remove the device care -
fully.
•
Remove the packaging material as well as the pack -
aging and transport bracing (if available).
• Check that the delivery is complete.
•
Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal -
lowing and suffocation!
4. Intended use
The bench-type circular saw is designed for the slitting
and cross-cutting of all types of timber, commensurate
with the machine’s size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed pur -
pose. Any use other than that mentioned is considered
to be a case of misuse. The user/operator and not the
manufacturer shall be liable for any damage or injury
resulting such cases of misuse.
The machine is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off
wheel. To use the machine properly you must also
observe the safety regulations, the assembly instruc -
tions and the operating instructions to be found in this
manual. All persons who use and service the machine
have to be acquainted with this manual and must be
informed about its potential hazards. It is also imperative
to observe the accident prevention regulations in force
in your area. The same applies for the general rules of
occupational health and safety.
1. Introduction
MANUFACTURER:
Jula Postorder AB
Box 363, SE-532 24 Skara, Sweden
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc -
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan -
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in -
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula -
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about
the associated dangers. The minimum age requirement
must be complied with. In addition to the safety require -
ments in these operating instructions and your country’s
applicable regulations, you should observe the generally
recognized technical rules concerning the operation of
woodworking machines.