MEDIZS Smart RK11 Скачать руководство пользователя страница 7

 

 

6

 

 

WARNING

 

Do not Keep way the place where the temperatures very much. 

 

CAUTION

 

This instrument is shipped with a grounding type power cable. To 
reduce  the  risk  of  electric  shock,  always  plug  the  cable  into  a 
grounded power outlet. 

 

CAUTION

 

Wipe the forehead rest with ethanol or glutaraldehyde solution to 
disinfect it each time a different examinee uses it, in order to prevent 
infection. 

 

CAUTION

 

Ensure  that  the  examinee  has  not  placed his/her hand  or fingers 
under the chin rest. Otherwise, hand or fingers may be hurt. 

 

1.

 

An exposure to the direct sunlight or very bright indoor lights may influence 
on  the result  of  accurate measurement.    Recommend to  use in  appropriate 
test room. 

2.

 

A sudden heating of the room in cold areas will cause condensation on the 
protective  glass  in  the  monitor  screen  and  on  optical  parts  inside  the 
instrument.  In  this  case,  just  wait  until  condensation  disappears  before 
performing measurement. 

3.

 

This instrument is used with accessories from MEDIZS. If consumer would like 
to use the accessories from other manufactures, safety of accessories should 
be verified and identified by manufacturer or by MEDIZS.   

4.

 

Operation manual should be keep at the place where the user can easily access. 

5.

 

This  instrument  can  be  installed  and  maintained  by  the  person  who  have 
completed training or education course. 

6.

 

When moving this instrument, please keep vibration or impact away from the 
equipment.  It  can  bring  some  damage  inside  or  outside  of  the  instrument. 
Please carefully handle the instrument. 

7.

 

When moving equipment, fix the stage, always keep power off, and then lift 
the bottom of the unit with both hands. 

8.

 

To  connect  this  instrument  with  other  relevant  equipment,  consult  with  the 
dealer about the way to make it. 

Содержание Smart RK11


















































Отзывы: