1.
It usually takes around 30-60 minutes for the belt or wrapping
pad to reach the maximum temperature if you put both a thick
protector and a thick blanket on top
. Cover the belt or wrapping
pad with a blanket and leave it periodically, checking how hot it
is under the blanket.
2. The
heating process stops and resumes again when the belt
or wraps cool down, to maintain the set temperature
. During
this time, the gems become very warm and emit radiant Far
Infra-Red rays.
3. For extra electrical safety the heating wires are positioned
in a short distance from the amethyst pad edges so that the
end tubes with crystals are heated indirectly by other stones.
It is normal when
these close to edges stones have a lower
temperature
.
4. When the heat is on, the surface temperature of the bare belt or
wrapping pad under the blanket, or under your body if you are
on the pad, becomes hot to touch.
At maximum heat level it
will reach 140-150 °F (60-65 °C) on the surface, if measured
immediately after you stand up or remove the thick blanket or
pillow. But if you measure the bare pad surface temperature
in several minutes again it will be much lower, around 110-
130 °F (40-50 °C)
. If the belt or wraps are uncovered, and
room temperature is low or the air flow is strong, it will cool the
pad very quickly. This is normal – when preheated, the crystals
transfer most of the energy in the form of Far Infrared Rays very
quickly.
5. If you keep your belt or wraps open without the protector pad,
blanket, or your body on it, the heat is dissipated – and though
the controller may continue to show rather high temperature
inside the belt’s or hands wrap’s heating elements,
the surface
will be merely warm to touch even on highest level
.
6. Sometimes when the belt or hands wrap starts to heat some
humming or buzz noise can be heard from the controller which
is quite normal. But
if the noise gets stronger or you feel any
smell or other signs of possible controller or belt or wraps
failure, please stop using the product and contact us.
7. It is OK for the controller to warm up a little when the belt or
wraps are on the highest heat level for a long time. But
it is not
normal if the controller gets really hot or if you notice any
smell
. Please turn off the belt or wraps and contact us for a free
replacement if this happens.
Remember not to put controller on
the belt or wraps heating pad, even if it is cool. It may heat
up and damage the controller
.
8. The most frequent reason for initial controller malfunction is an
incorrect order of connection.
It is necessary to connect the belt
TIPS: USING YOUR BELT OR WRAPS
1. Please
study the Catalog and User Guide
included with your
product before first use. They are easy to operate but the User
Guide has important safety information and a lot of different
useful tips that may help you get more benefits and accelerate
the learning curve. Be sure to
completely study the list of
contraindications and discuss them with a health professional
.
2. Subscribe to MediCrystal® on youtube for educational videos.
Our
youtube channel is
https://www.youtube.com/MediCrystal
3.
Consult your doctor how to use
, especially it is important if you have
any chronic disease. Even if your health professional is not familiar
with hot crystal FIR, doctors usually can give good advice about how
such or similar well-known technologies like sauna or heating pads
will work, especially in the case of any existing health condition.
4. When you get the box with your product, if it is too cold or too
hot or wet outside, please,
keep it inside for an hour
to adjust
to room temperature and humidity before connecting to the
power socket. Open the box and take out your product carefully,
especially if it is a heavy one you may need someone’s help.
Check that all accessories are included.
Put it on the floor, bed
or other flat surface with the crystals side facing up
.
5. Our products have special layers in the bottom that reflect the
heat upwards. But
if you use them laying on a hardwood floor
or on a memory foam mattress and the heating pad is under
your body, it may be better to put a towel beneath
to dissipate
any remaining heat.
6. If your area is subject to frequent electrical blackouts or power
spikes,
it could be better to connect your product to electricity
through a surge protector
, AVR or UPS device similar to that
one which protects computers or refrigerators. It will protect the
controller from any malfunctions resulting from a power surge.
Please remember
to turn the controller OFF and unplug your
product from the power socket after use
.
7. The first heating should be to
test your product at the highest
temperature level
(70 °C equal to 158 °F) for 2-3 hours. This
will also help purge any possible odors from the fabric and other
layers’ remaining volatile particles. If you are oversensitive to
smells you may choose to air it out in a garage overnight. Our
mats and pads are made from the highest quality, ‘zero-emission’
materials but it is still better to do this. Do not put the protector
on the product or lay on it during this time.
8.
Find a secure, dedicated area with calm surrounding and good
time to use your product
with some degree of concentration.
Put up “do not disturb signs” and play some soothing music to
enhance your experience. Put on comfortable sleepwear and
relax. It may be a good idea to
clean and scrub your body
to open the pores before your sessions
, as this will facilitate
sweating and detoxification. You can preheat your belt, vest or
wraps and wear them concealed under clothes walking or running
outside. Mats are stationary and better to use them at home.
or wrapping pad to the controller first, TIGHTLY, and only after
this should you plug the controller into the outlet, then turn it
on and set the timer
. After this you may set desired temperature.
When you disconnect, first turn the controller to OFF, then
disconnect the plug from the socket – and only after this (and
only if it is necessary), unplug the controller from the belt or
wraps.
9.
Do not disconnect the controller from the belt or wraps more
frequently than necessary
, in order to avoid the connection
becoming loose. If you connect the controller to the power
source first (before connecting it to the belt or wraps),
the safety
program will lock the controller and put it in ‘safe’ mode
.
It may start to beep or will show OF or other error code on the
screen. To reactivate the controller simply reconnect it in the
correct order.
10. Choose the best position. FIR amethyst rays penetrate deep and
may awake resonant vibrations on micro level so that even after
the session is over the body temperature may stay elevated to
normal level of 98.6 °F for up to 8 hours, which is good for
activity and rejuvenation. This phenomenon is described in the
European bestseller «98,6 – Ideal Body Temperature as the Secret
to Optimum Health» by famous German naturopath Dr Uwe. But
there is also the local effect when those tissues which are closest
to the belt or wraps receive more heat. It may be beneficial for
them, but the highest levels may also cause some issues with
movement if you have stones, etc.*
11.
If the product feels hard at the starting point, it is essential to
cushion it and eliminate the crystals’ pressure correctly.
Put on
top a 3-D pad, and a cover included into the set of your product.
You can add several layers of bamboo, cotton sheets or towels, but
not more than one inch thick to make your mat even softer. As soon
as your body gets used to the crystals’ pressure, you may choose
to remove the extra layers one-by-one. Protectors and towels are
great for sweat absorption during heating sessions or for moderate
cushioning, but for high intensity, it may be better to use your
mat without any covering. With FIR, some of the heating rays will
dissipate if you use a thicker layer on top of the stone mat and
under your body. The same applies to negative ions, but most will
still travel through. As for longer sessions, even with covers the
product can still be too hard to sleep and too heavy to remove it
from your bed every evening (especially if you have a large size
mat). A simple solution is to put a 3-4 inch thick mattress pad on
top, which is lighter and easier to handle than the stone mat. Be
aware that you can cover your product with a thicker than one-inch
layer or a non-permeable foam pad ONLY after the mat cools down.
To avoid overheating and fire risks
NEVER
heat your product with
the topper or thick layer on it. Always remove the topper first and
stenosis, myocardial infarction, heart attack, unstable angina
pectoris, if you take corticosteroids or have brain or other tumors.*
6. Anybody with diseases associated with a reduced ability to sweat or
insensitivity to heat should use products without heat, in negative
ions mode. Diabetic neuropathy may be a contraindication because
some diabetic patients loose sensitivity to heat.*
7. Nobody with diagnosed diseases, ailments or medical conditions
should ever use these products without approval from and/
or supervision of a physician. It may be extremely dangerous to
raise the body temperature to high levels for people with: Adrenal
suppression disorders, Addison’s disease, adrenal Insufficiency,
systematic lupus erythematous, multiple sclerosis (MS), brain
tumors, bypass surgery, high hypertension or some other
conditions.*
8. Anybody taking medications or currently going under medical
treatments, radiation or chemotherapy should consult a physician
before using the products in heating mode. Some medicines as
diuretics, barbiturates, and beta-blockers may impair the body’s
natural heat loss mechanisms. Some over the counter drugs such as
antihistamines, blood thinners may also cause the body to be more
prone to heat stroke. Sleeping aids, pain killers, narcotics, anti-
psychotic medicines may be the most dangerous in impairing one’s
judgement. People under influence of drugs, alcohol or intoxication
as well as patients with mental impairments or dementia should never
use the hot stone mats,pads, wraps, belt or other heating devices.*
9. Anybody experiencing a high fever should not use theproducts in
heating mode. Only the negative ions function can be used until the
fever stops.*
10. If you use heating creams or balms, liniments, salves or ointments
that contain heatproducing ingredients, you should never use them
with the belts, pads, wraps, mats unless recommended by a health
care professional so as to avoid burns.*
11. Anybody with fresh wounds, trauma, joint injuries or swollen hot joints
where the cold practices is necessary should not use any FIR mat, belt or
pad in heating mode, so as to avoid exacerbating any inflammation.*
12. Anyone with a mental or physical disability or those with limited
mobility should use ThermoGem™ products in the negative-ions-only
mode unless under full supervision of a medical professional and
have a doctor’s approval.*
13. It is not recommended to use any part of the heating area of your
product directly on your head. Our brains do not have same efficient
cooling system as the other body does.
14. Stop using the products if any known conditions worsen while using
it. Pain should not be experienced when using them. However,
the infrared heat will go to areas of disease or discomfort – some
people may perceive this as pain and others as a sensation. If pain is
persistent, discontinue use.*
If you have any of these conditions, avoid using the products
completely unless under the care of a doctor with expertise in hot
stone or sauna detoxification.
While the above are some of the conditions which may pose dangers
definitely check with your doctor or a health professional experienced
in Far Infrared or sauna practices about your specific medical condition.
Remember that it is very important to properly hydrate with
pure and mineralized water before and after sessions especially if
you sweat and loose electrolytes. It will help to avoid dry mouth
feeling, weekness and other symptoms of dehydration. A general
rule of thumb is to never begin a session thirsty or dehydrated and
drink a lot of mineral water, herbal teas or juices.
TIPS: BEFORE YOU START
*MediCrystal® and ThermoGem™ products are not intended to diagnose, cure, treat, mitigate or prevent any disease, illness or medical condition or to substitute for medical treatment of any
kind. Information here is never to be construed as medical advice. These products and statements have not been evaluated by U.S. FDA (please, see Disclaimer in this user guide, page 11).
®
®
USER GUIDE
6
www.MediCrystal.com
7
Содержание ThermoGem Bio-Magnetic Photon Belt
Страница 1: ......
