mecalac TA1EH Скачать руководство пользователя | Manualshive

Страница: 99 / 112

background image

Page 12 - 2

TA1EH

12. Storage, Decomissioning & Disposal

•

Exhausts – Cover exhaust stack openings with plastic or waterproof paper and secure with

adhesive tape.

•

Air Intakes – Cover air intake openings with plastic or waterproof paper and secure with `

adhesive tape.

•

Hydraulic Control Valves – Where possible position hydraulic controls for minimum

exposure of valve spools (spool inside valve body). Coat the remaining exposed spool
surface with a suitable oil or grease.

•

Hydraulic Cylinders – Where possible retract cylinders for minimum rod exposure. Coat the

remaining exposed piston rod surface with a suitable oil or grease. For machines with blade,
bucket, attachment which is not mounted, wire the cylinder to prevent rod drift.

•

Control Cables and Linkage – All exposed linkage, clevis ends, ball joints etc. which are not

protected during “lubrication” should be protected by a suitable oil or grease.

•

Open Ports and Hose Ends – Plug or seal with adhesive tape all open ports.

•

Machined Surfaces – Coat any exposed machine bores and surfaces with a suitable rust

preventative.

•

Note: Do not apply oil or grease to brake discs.

•

Hinges – Apply oil.

•

Seat Slide Adjusters – Coat with grease.

•

Seats, Armrests and Cushions – When machine is not equipped with a cab, cover these
items with plastic or waterproof barrier paper, and secure with adhesive tape. Provide an
opening in the underside of the protective materials to prevent condensation build up.

•

Cabs – All windows, doors and vents must be closed.

•

Hoods, Hoodsides, Covers, Panels, etc. – must be installed and closed.

•

Security Panels and Security Locks – must be installed and locked.

12.3 Extended Storage – Under Six Months

When storing a machine for periods longer than 30 days, but less than six months, the following
procedures must be followed, in addition to the procedure described above.

•

Engine – Consult the relevant engine manual/dealer for storage procedure for periods longer

than 30 days.

• Transmission – Consult the relevant transmission manual/dealer for storage procedure for

periods longer than 30 days.

• Batteries – Remove battery from the machine and store in shop. Protect batteries from

temperature extremes. Coat the terminals and cable ends with acid resistant petroleum jelly.

• Vents and Breathers – Remove all vents and breathers and plug openings with pipe plugs or

seal with adhesive waterproof tape.

• Belts – Release tension on all belts.

«
...
97
98
99
100
101
...
»

Содержание TA1EH

















































































































Отзывы:

Нет отзывов

Похожие инструкции для TA1EH

Бренд: U-Line Страницы: 3

Бренд: SANO Страницы: 8

Бренд: Taylor-Dunn Страницы: 52

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 15

RoGator 64 Series

Бренд: Raven Страницы: 80

Бренд: Kia Страницы: 262

Бренд: LOADMASTER Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды