mecalac TA1EH Скачать руководство пользователя

Страница: 61 / 112

Page 6 - 2

TA1EH

6. Initial Setup & Adjustments

6.3

Start Up and Adjustments

When all delivery checks have been made and the ROPS has been placed and secured in the
work position:

• Check that the Forward/Reverse switch is in Neutral.

• Start the engine and allow to run for a few minutes to warm up.

• Check all instruments and warning lights are functioning correctly.

• Check lighting and indicators operate (if fitted).

• Stop the engine and check for any fluid leaks or signs of overheating.

• Re-start the engine, drive the machine a short distance to check operation of transmission,

brakes and steering.

• Check if the skip tips, raises and lowers.

• Park up and stop the engine.

• Report and have rectified any faults before placing machine into service.

PROCEDURE

1. Remove the linch pins from the locking pins either side of the ROPS.

2. Remove the locking pins.

3. Push the top half of the ROPS upwards to the working position.

4. Refit the locking pins.

5. Secure the locking pins in position with the linch pins.

6. Remove the rubber cover and fit the beacon to the stem on top of the ROPS.

7. Switch on the beacon and check it is working correctly.

Содержание TA1EH

















































































































Результаты поиска

Содержание TA1EH

Отзывы:

Похожие инструкции для TA1EH

Бренды по названию

Популярные бренды

mecalac TA1EH, Руководство оператора

Результаты поиска

Содержание TA1EH

Отзывы:

Похожие инструкции для TA1EH

Бренды по названию

Популярные бренды