Mec 2047ES Скачать руководство пользователя страница 60

Страница: 60 / 104

March 2008

"2047ES / 2647ES / 3247ES" Service & Parts Manual - CE Specifications

Page 4-8

ART_2193

Bearing

Steering

Shaft

Steering

Link

Steering Cylinder

Steering Link

Steering Stop

Bearing

Spacer

Washer

Steer Cylinder

There is one (1) double acting type steer cylinder on this machine. During operation, cylinder
should not leak, but a slight damping at the rod seal is acceptable.

To replace steer cylinder:

CAUTION:

• Clean all fittings before disconnecting hoses.
• Tag hoses for proper reassembly.
• Plug all openings to prevent contamination.

1. Raise and support the front end of machine (see

Raising the Machine).

2. Disconnect hydraulic hoses and cap them.

3. Remove the bolts holding the steering cylinder to the steering links and move the steering

links away from the cylinder.

4. Remove the steer cylinder

mounting bolts.

5. Carefully remove the steer

cylinder.

6. Position the new steer cylin-

der and install the mounting
bolts.

7. Move the steering links into

position and install the hard-
ware.

8. Connect hydraulic hoses.

9. To purge air from cylinder;

• place a suitable

container beneath the
hose connections to
catch spilled oil,

• loosen hose fittings

slightly,

• actuate steer function,

• when all air is purged,

tighten hose
connections.

Steer Cylinder Seal Replacement

Refer to

Section 1 for seal replace-

ment instructions.

Содержание 2047ES









































































































Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды

Mec 2047ES, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды