Mec 2047ES Скачать руководство пользователя страница 41

Страница: 41 / 104

"2047ES / 2647ES / 3247ES" Service & Parts Manual - CE Specifications

March 2008

Page 3-7

GP102 LED Flash Codes

The

GP102

has a built-in LED to provide simple diagnostics when no

EZcal

is available. Please note

that the use of an

EZcal

provides significantly better diagnostics through the HELP messages. An

EZcal

is also necessary to calibrate a

GP102

LED on steady

This indicates no fault with the

GP102

LED off always

This indicates no power to the

GP102

, or idle timeout (if enabled - activate a lift or drive function to

cancel the idle timeout)

LED flash code 1

This indicates the

GP102

has not been properly calibrated.

LED flash code 2

This indicates a fault with the switch inputs to the

GP102

. Check wiring to connector P2.

LED flash code 3

This indicates a fault with the shutdown outputs of the

GP102

- a short to the supply has been detected.

Check wiring from pins P3-4.

LED flash code 4

This indicates that armguard is active, or that there is a fault with the elevation switch - the

GP102

verifies correct opening and closing of the elevation switch against the height sensor. Checking the
elevation switch on P2-10. If the height sensor has been adjusted or replaced, repeat the CALIBRATE
HEIGHT procedure.

LED flash code 5

This indicates a fault with the shutdown outputs of the

GP102

- a short to 0V (ground) has been

detected. Check wiring from pins P3-4.

LED flash code 6

This indicates a fault with the load measurement - check the pressure sensor and wiring from it to
connector P4.

LED flash code 7

This indicates a fault with the supply to the

GP102

- check battery supply at least 8V on pin P2-12; also

check that there is not a short to 0V (ground) on pin P4-1.

LED flash code 8

This is not a fault - it indicates the

GP102

has prevented a function; functions can be prevented if the

platform is overloaded, if the machine is tilted too far, or if the platform is too high.

LED flash code 9

This indicates a fault with the height measurement - check the height sensor and wiring from it to
connector P4.

LED flash code 10

This indicates the

GP102

is carrying out start-up tests.

LED flash code 15

This indicates the

GP102

is in “FACTORY OVERRIDE” and overload functions are disabled - this aids

manufacture by allowing vehicle movement before the machine is built sufficiently to be calibrated. 15
flash will be present whenever a

new circuit board is installed previous to calibration.

Содержание 2047ES









































































































Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды

Mec 2047ES, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды