Mec 2047ES Скачать руководство пользователя страница 58

Страница: 58 / 104

March 2008

"2047ES / 2647ES / 3247ES" Service & Parts Manual - CE Specifications

Page 4-6

Front Drive Motors

There are two (2) hydraulic motors on the front axle. These can be damaged or leaks may occur;
repair or replace as necessary. Refer to

Section 1 - Hydraulics for motor service and repair proce-

dure.

CAUTION:

• Clean all fittings before disconnecting hoses.
• Tag hoses for proper reassembly.
• Plug all openings to prevent contamination.

Front Drive Motors

Remove.

1. Loosen the lug nuts.

2. Raise and support the front end of machine (see

Raising the Machine).

3. Remove the wheel and tire assembly to access drive motor.

4. Disconnect the Steering Linkage (refer to illustration).

5. Remove the steering stop (refer to illustration).

6. Remove the cotter key, motor

shaft nut, and hub from the
drive motor shaft.

7. Turn the motor housing to

gain access to the motor and
hose assemblies.

8. Disconnect hose assemblies

from drive motor.

9. Remove the cap screws and

remove the drive motor.

Replace

Installation is reverse of removal.

ART_2187

Steering Linkage

Steering Stop

Motor Shaft Nut

Motor

Motor Mount Bolts

Motor Mount

Nuts

Motor Mount

Hub

Lug Nuts

75 - 85

102 - 115

Motor Mount Bolts

65 - 72

88 - 97.5

Motor Shaft Nut

350

475

Steer Linkage Bolts

26 - 28

35 - 38

Steer Stop Adjustment Bolt

26 - 28

35 - 38

Steer Stop Mount Bolts

86 - 96

116 - 130

TORQUE Ft.

lbs.

Содержание 2047ES









































































































Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды

Mec 2047ES, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание 2047ES

Отзывы:

Похожие инструкции для 2047ES

Бренды по названию

Популярные бренды