background image

Telescope Features  ...................................................... 8

Assembly ........................................................................ 5

Assemble the Base .................................................. 5

Assemble the Tube .................................................. 6

Insert Eyepiece, Attach Red Dot Finder .................. 7

Collimating the Optical System ................................ 8

Align the deluxe Red Dot Finder ..............................11 

Using a Dobsonian Telescope ..................................11

Calculate Magnification ............................................12  

Observing ......................................................................12

Some Tips ................................................................15

Care of the Optics ....................................................15

Meade Customer Service ..............................................16

Specifications ................................................................17

Optional Accessories......................................................19

Appendix A: Altitude Adjustment Knobs ........................21

CONTENTS

WARNING!

Never leave the primary mirror uncov-
ered during the daytime unless using
the telescope to view terrestrial objects.

® The name "Meade" and the Meade logo are trademarks

registered with the U.S. Patent and Trademark Office and in

principal countries throughout the world. "LightBridge " is a

trademark of Meade Instruments Corporation.

© 2006 Meade Instruments Corporation.

 

 

 

 

Содержание LightBridge Truss Tube 10

























Отзывы: