background image

19

Looking at or near the 

Sun

will cause 

irreversable

damage to your eye. Do not point

this telescope at or near the Sun. Do not look through the telescope as it is moving.

16" Deluxe Model

OTA

Open truss design.  Upper cage metal tube 

containing spider and secondary mirror holder,

focuser with attachment points for truss tubes.

Lower metal tube containing mirror cell, altitude bear-

ings, battery powered fan, with truss tube attachment 

castings and captive bolts and knobs. 

All 16 inch models have a triangular ground plate.  

Truss tubes  

Silver anodized aluminum with attachment hardware

and captive bolts.  Machined aluminum altitude 

bearings.

Secondary Mirror Support

4-vane, steel

Mirror

16" (406mm) 

Focal length

1829mm (72") 

Focal ratio

f/4.5 

Resolving Power

0.45 arc seconds

Limiting visual magnitude

14.5

Focuser

10 to 1 dual-speed 2" Crayford style machined 

aluminum with 1.25” adapter. 

Mount

Swivel base with Teflon bearings for azimuth.

Eyepiece tray

For one 2” and three 1.25” eyepieces mounted on

one side of the base.

Counterweight

None

Eyepiece

Meade 26mm Super Plössl

Dust Cover

To fit over primary mirror inside of lower tube.

Finder

Standard red dot 

Computer Software

CD-ROM of Autostar Suite Astronomer's Edition 

software

Assembled OTA weight

74 lbs.

Assembled Mount weight

54 lbs.

Total Assembled telescope wt. 128 lbs.

 

 

 

 

 

 

 

Содержание LightBridge Truss Tube 10

























Отзывы: