McQuay Suite II, Установка и обслуживание данных

Страница: 5 / 28

IM 671 / Page 5 of 28
A heavy-gauge, corrosion resistant cabinet/wall sleeve is provided for each unit. The cabinet/wall sleeve is either shipped in a
separate carton or shipped in a multi-pack of 15.
The standard cabinet/wall sleeve is designed to be easily in-
stalled in a variety of wall constructions.
Note: The center of gravity is 10
1
⁄
4
"
(260mm) from the rear
face of the wall sleeve. The wall sleeve must be inserted into
the was at least 10
1
⁄
4
" (260mm) or other support must be em-
ployed.
Support can be from a factory supplied subbase or from other
field supplied materials, the wall sleeve is not intended to re-
place the lintel. Recommended installation procedures are de-
scribed below:
1.
Clean the opening of all debris that may interfere with
installation.
2. If the unit is to be supplied with a subbase, refer to page
9 for installation procedure. Install subbase before install-
ing cabinet/wall sleeve.
3. If the optional drain kit is to be employed refer to page 10
before proceeding.
4. Place a thin pad of soft mortar on bottom of the opening
and slide in the cabinet/wall sleeve. Be sure to recess the
wall sleeve enough to accommodate outside louver. This
recess is
3
⁄
8
" (9.5mm) for stamped louvers and 1
1
⁄
8
" (32mm)
for architectural louver. Louver should be flush to exterior
surface when complete. Note: Do not recess if using the
external drain kit - see pg. 10.
5. Level cabinet /wall sleeve in both directions and secure
by anchoring with appropriate fasteners (as shown in fig-
ure C page 8). A
5
⁄
16
" (8mm) hole is provided on each side,
2" (51 mm) down from the top and 2" (51 mm) in from the
rear of the cabinet/wall sleeve. Additional holes may be
required to firmly secure the cabinet/wall sleeve.
Caution: Do not drill holes in the subbase of the cabi-
net/wall sleeve. Where a subbase is used, secure wall
Wall Sleeve Installation – Frame and Brick
Note: Standard Subbase is available in 3" (76mm) or 4" (102mm) height.
Leveling legs provide adjustment of 1" (25.4mm).
Figure 4. Frame & Brick with Standard Electric Subbase
Figure 6. Frame & Brick with Hydronic Subbase
Figure 5. Panel Wall Construction with Cord Connection
sleeve to subbase with clips provided.
6. Caulk the cabinet/wall sleeve to the wall opening on both
inside and outside perimeter. Be careful not to plug the
weep holes. Caulking should be resilient, non hardening
type such as silicone.
Finished Floor
or Carpet
13
3
⁄
4
"
(349mm)
16"
(406mm)
3" (76mm)
17"
(406mm)
Wall Receptacle
by Others
Caulk
Perimeter
Both
Indoors &
Outdoors
Outdoor
Louver
Steel Lintel
(by Others)
Mounting
Screws
by
Installer
Finished Floor
or Top of Carpet
13 3 ⁄
4
"
(349mm)
16"
(406mm)
17"
(406mm)
Power Supply
Connect
(Alternate Entry)
Caulk
Perimeter
Both
Indoors &
Outdoors
Before
Installing
Louver
Outdoor
Louver
Steel Lintel (by Others)
Mounting
Screws
by
Installer
4
3
⁄
8
"
(111mm)
Room
Cabinet
8 1 ⁄
4
"
(203mm)
Leveling
Leg
See Note
Wall Sleeve
Finished Floor
or Carpet
16"
(406mm)
17"
(406mm)
Caulk
Perimeter Both
Indoors & Outdoors
Outdoor
Louver
Steel Lintel (by Others)
Mounting
Screws
by
Installer
Room
Cabinet
8
1
⁄
4
"
(203mm)
Leveling Legs w/1"
Adjustment
Hydronic Subbase
Wall Sleeve
Subbase
Side Channel
Alternate
Electrical
Connections
Hydronic
Heating Coil
8
1
⁄
4
" (203mm)
13
3
⁄
4
"
(349mm)