mcmurdo S4 Rescue SART Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 27

background image

Commercial in confidence

Page 23

mcmurdo

mcmurdo

mcmurdo

mcmurdo

8. END OF LIFE STATEMENT

At the end of the SART’s useful life, it is vital that the battery be disconnected from the main unit
to prevent false alarms. False alarms cause expensive disruption to Search and Rescue services
and may endanger lives as a consequence. It is also necessary that the SART and its battery
pack be disposed of in a manner that does not present a threat of environmental damage.

8.1.

Battery Removal

To disconnect the battery, turn the SART over and remove the three battery retaining screws
using a cross headed screwdriver. Gently prise the battery from the main unit; Note that this will
also release the ‘O’ ring seal. Cover the terminals of the battery pack with sticky tape to prevent
inadvertent short-circuiting.

8.2.

Disposal

The Waste Electrical and Electronic Equipment (WEEE) Directive aims to minimise any adverse
impact of electronic equipment on the environment, both during the product lifetime and when it
becomes waste. Within the European Union this legislation is mandated by Directive
2002/96/EC, and there is similar legislation in most other continents. The directive applies to all
electronic products such as IT, household appliances, portable electronics etc., and imposes
requirements to collect, treat, recover and recycle each product at its end of life. Electronic end-
user products must also carry a WEEE label (as below) and recovery and recycling information
has to be provided to the recycler.

This SART product contains traces of lithium in the battery pack. In addition it may contain lead
and brominated flame retardants (BFRs), both in the housing material and circuit boards.
In  keeping  with  the  directive,  McMurdo  strongly  recommends  that  this  SART  product  and  its
battery pack be disposed of in a sensible and considerate manner. For example, do not simply
discard  the  product  in  the  domestic  waste.  Instead  take  it  to  a  civil  recycling  facility,  or  contact
McMurdo for advice.

«
...
24
25
26
27
»

Содержание S4 Rescue SART




























Отзывы:

Нет отзывов

Похожие инструкции для S4 Rescue SART

Бренд: Icom Страницы: 47

Бренд: Yacht Sentinel Страницы: 19

Бренд: jotron Страницы: 26

Бренд: Kayoba Страницы: 11

Бренд: ZF Страницы: 56

Бренд: Hyundai Страницы: 9

Бренд: Magnasonic Страницы: 10

Бренд: Halma Страницы: 36

Бренд: Garmin Страницы: 62

Бренд: AEG Страницы: 86

Бренд: AEG Страницы: 58

Бренд: AEG Страницы: 66

Бренд: AEG Страницы: 78

Бренд: AEG Страницы: 46

Бренд: AEG Страницы: 98

Бренд: AEG Страницы: 126

Бренд: AEG Страницы: 86

Бренд: AEG Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды