Mclennan SimStep Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 32

background image

SimStep

Manual - 3400 Iss. D

7

th

June 2004

page 31

12 Limitations of Use

This system has been designed to drive a hybrid type stepper motor. Any other use has
not been considered, therefore could damage the drive and could be dangerous for the
users.
Good engineering practices should be employed when using this product.

The operating temperature should be between 0ºC and 30ºC.

Users should take suitable precautions in the application of this product, to ensure that the
overall system complies with EN50081-1 and EN50082-1 (EMC directive).

These products should not be put into service until the machinery in which they are
incorporated has been declared in conformity with the provisions of The Supply of
Machinery (Safety) Regulations 1992 and The Supply of Machinery (Safety) (Amendment)
Regulations 1994 (Machinery Directive).

Motor control systems are inherently hazardous. Even a small motor, if coupled to a
leadscrew, gearbox, or any other form of mechanism that provides a mechanical
advantage, can generate considerable force and could cause serious injury. Incorrect
operation can also lead to damage to the motor or associated machinery.

«
...
30
31
32

Содержание SimStep

































Отзывы:

Нет отзывов

Похожие инструкции для SimStep

Бренд: zipwake Страницы: 12

Бренд: Watts Страницы: 2

Бренд: jbc Страницы: 12

Бренд: Tapeswitch Страницы: 13

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Baby Jogger Страницы: 16

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Oldham Страницы: 32

Бренд: H3C Страницы: 14

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды