background image

13

Output 2

Outputs 1 and 2 can be toggled On and Off through 

the Trim settings. Output 2 is also called a SUB out 

and may be connected to a Subwoofer. Output 2 is 

full range and stereo and can be attached to another 

amplifier perhaps in another zone (room). Using this 

Trim Function is an easy way to toggle this zone On 

and Off. 

Meter (Amp) Lights

This setting controls the status of meter lights of a 

McIntosh amplifier controlled through a connected 

Power Control (Trigger) cable (see “Power Control 

(Trigger) Outputs” on page 11). 

Display Brightness 

Display Brightness can be set to Always On and 

Auto Off. Turn the Right Knob clockwise or use 

the Right Arrow on the Remote Control to select 

Always on. Continuing to turn the knob or pushing 

the Right Arrow will cycle through four brightness 

settings: 25%, 50%, 75% and 100%. 

Turning the Right Knob counterclockwise or 

pushing the Left Arrow on the Remote Control 

will select Auto Off. Continuing to turn the knob 

or pushing the Left Arrow will cycle through four 

brightness settings: 25%, 50%, 75% and 100%. 

When set to Auto Off, the C8’s display will blackout 

when no input is received for 10 seconds. Turning 

the Left Knob or pushing it twice will awaken the 

display.

Setup Settings

To enter the C8’s Setup menu, press and hold the Left 

Knob for 2 seconds. The VFD (display) will change. 

Rotate the Left Knob to scroll through the available 

screens. Push and release the Left Knob to exit a 

menu.

Firmware and Serial Number

This screen display the current firmware version as 

well as your unit’s serial number.

Input Setup

To edit Input information, press and hold (two 

seconds) the Left Knob at the Setup: Inputs menu 

(see Figure 12 ). 

Rotate the Left Knob to view the Inputs

• 

Balanced

• 

Unbal 1

• 

Unbal 2

• 

MM Phono

• 

MC Phono

(If DA2 Expansion (see “DA2 Expansion Slot” on 

page 11) has been added, additional Inputs will 

appear).

The selected input can be turned On (default) or Off 

by turning the Right Knob. If On is selected, the 

Input can be renamed. To rename the selected input, 

press and hold the Left knob until the RENAME 

screen appears. Turn the left knob to select the 

character to change and the right knob to select 

characters. When your changes are complete, press 

and hold the Left Knob for two seconds to save. You 

will return to the previous screen with the new name 

visible. 

An Input that has been turned Off will not appear as 

an available Input when scrolling. To make it visible 

again, set the Input to On. 

Output 2 (SUB)

Output 2 also know as SUB Output can be set to 

Stereo (default) or Mono.  Output is full range and 

stereo so if using only one channel (left or right) of 

the output, Output 2 should be set to Mono. Turn the 

Right Knob to change selections. 

Trigger Setup 

The C8 has three Power Control Outputs or 

Triggers. The Main Trigger sends power commands 

to attached components based on the overall power 

status of the C8 (On or Off). Trigger 1 and Trigger 

2 can be set to act like the Main Trigger or be 

assigned to follow Output 1 or 2 or any Input’s 

status. 

The default of Trigger 1 and Trigger 2 is Main. To 

change the setting for Trigger 1 or 2:

• 

Scroll to “Setup: Triggers” in the Setup Menu

• 

Press and hold the Left Knob for two seconds 

• 

Turn the Left Knob to select Trigger 1 or 

Trigger 2 to edit

• 

Turn the Right Knob to select Main, Output 1, 

Output 2 or Input

• 

To choose an Input, press and hold the Left 

Knob for two seconds. Turn the Left Knob to 

scroll through the Inputs. Turn the Right Knob 

to select On or Off. Selecting On will send a 

Figure 12–  Inputs Menu

Содержание C8 - SCHEMATICS





















Отзывы: