background image

11

• 

Turn the Right Knob clockwise for Enabled 

(on) or counterclockwise (off)

• 

Press and release the Left Knob to exit the 

Setup menu

DA2 Expansion Slot

The C8 has an expansion slot to allow for the 

installation of the DA2 Digital Audio Module. The 

DA2 will add the following digital audio inputs:

• 

two coax

• 

two optical

• 

one HDMI (ARC)

• 

one MCT

• 

one USB audio

Due to the technical nature of the DA2 upgrade, 

the upgrade 

must be performed by a qualified 

trained professional at an Authorized McIntosh 

Dealer or Authorized McIntosh Service Agency

Please note that if the upgrade is performed by 

anyone other than an Authorized McIntosh Dealer 

or Authorized McIntosh Service Agency, under 

the terms of your McIntosh Limited Warranty any 

resulting damage or failure of your unit will be 

excluded from warranty coverage. Contact your 

local Authorized McIntosh Dealer or Authorized 

McIntosh Service Agency to schedule your upgrade 

if you wish to add digital capabilities to your C8.

AC Power

This connection is essential. Plug the female end of 

the supplied AC Power Cord into the AC connector 

(standard 15 ampere IEC) located in the rear right 

corner of the C8. Plug the male end of the AC 

Power Cord into a grounded and functioning AC 

outlet. 

Power Control (Trigger) Outputs

The C8 has three Power Control Outputs or 

Triggers:

• 

MAIN

• 

TRIG 1

• 

TRIG 2

Power Control enables power on/off signals to go to 

connected components so that other components can 

automatically powered on (or off) as called for by 

the C8. 

Connect components to the Triggers using a 3.5mm 

stereo mini plug. see Figure 10. The Triggers work 

by sending on/off signals in the form of +12 volt/0 

volt to connected McIntosh components.

“Trigger Setup” on page 13.  

Power

Control

Meter

Illumination

Control Ground

 

Passthru

The C8’s  PASSTHRU feature allows your 

2-channel system to be incorporated into a 

multichannel system, typically as the left and right 

front speakers. When the connected unit (Master)

powers on, it will take control of your C8. The C8 

will send the signal to your amplifier and speakers 

at a volume controlled by the Master. The C8 

preamplifier is now a slave to the source unit and 

you cannot control the sound from this unit until the 

source unit is shutoff or disconnected.

To use the  PASSTHRU feature, connect the 

controlling unit to the C8’s PASSTHRU connector 

using the same type of cable as used for Power 

Control (Trigger) Outputs. The C8 PASSTHRU jack 

should be connected to a Power Control Trigger 

Output of the controlling unit. 

To enable (or disable) PASSTHRU, enter Setup. 

When enabled, an Input must be assigned to 

PASSTHRU. When in PASSTHRU mode, the C8 

will send the signal from the assigned Input to the 

C8’s Outputs. The volume will be dictated by the 

controlling unit. 

To turn off or assign an Input for PASSTHRU:

• 

Press and Hold the Left Knob for two seconds

• 

Turn the Left Knob to the menu choice 

“SETUP: PASSTHRU”

• 

Turn the Right Knob to scroll through the 

following options:

• 

Off

• 

Balanced

• 

Unbal 1

• 

Unbal 2 

(Note: if you have changed an Input’s 

name, the new name will appear.)

• 

Press and release the Left Knob to exit Setup. 

Your choice will be saved

When in PASSTHRU mode, control of the 

C8 is limited to the Trim functions: DISPLAY 

BRIGHTNESS and AMP METER LIGHT. To 

regain controls, the Controlling unit must be shut (or 

Power Control cable removed from the PASSTHRU 

connector.)

Data Out

The C8 will convert IR Remote Control data to 

share with McIntosh components connected to the 

DATA PORTS. This will allow units that are out 

of range of an IR signal to receive commands. A 

McIntosh source can thereby be controlled by the 

C8 Remote.

Figure 10–  Power control (trigger) mini plug

Содержание C8 - SCHEMATICS





















Отзывы: