background image

4

Unpacking the MC75

Caution

To prevent damage to the MC75 

Tubes during shipping, there is a 

special foam insert surrounding the 

Tubes of the Power Amplifier.

The Foam Insert must be 

removed from the MC75 be-

fore connecting the AC Pow-

er Supply Cord to the power 

amplifier.

Failure to do so has the po-

tential of a Fire Hazard, 

resulting in damage to the 

MC75 and the surrounding 

environment. 

Follow these instructions for 

removal of the packing foam 

before connecting the AC 

Power Supply Cord to the 

MC75.

In order to remove the foam insert sur-

rounding the tubes on the MC75, it is necessary 

to temporarily remove the Tube Cover. After 

the foam insert is removed, the Tube Cover is 

re-installed and should not be removed. The 

cover provides protection from the hazardous 

voltages inside the MC75. The MC75 has no 

Figure 2

Tube Cover

user serviceable parts, including the tubes. If 

repairs are needed they must be performed by 

an authorized McIntosh Service Agency.

1. Orient the MC75 so the Front is facing you and 

remove the Warning Sheet. Refer to figure 1.

2. Using a Philips Head #2 screw driver, remove the 

Tube Cover Screw securing the Tube Cover to the 

chassis on each side of the MC75. Refer to figure 

2. Carefully lift up and remove the Tube Cover 

from the MC75. Refer to figure 3.

3. Place the Tube Cover and the previously removed 

chassis screws in a safe location, as the Tube 

Cover will be reinstalled.

Figure 1

Tube Cover

Remove Foam 

Insert located 

under the Tube 

Cover

4. Carefully lift up and remove the Foam Insert from 

the MC75 exposing the Tubes. Refer to figures 4 

and 5.

5. Carefully reinstall the previously removed Tube 

Cover using a Tube Cover Screw on each side of 

the MC75. Refer to figures 6, 7A, 7B and 8.

Note: Only use the chassis screws supplied with the 

MC75. If you can not find the chassis screws, 

contact the McIntosh Parts Department for 

replacements.

6. Save the Foam Insert and Warning Sheet with the 

MC75 Shipping Carton for possible future use.

Remove the 

Warning Sheet

Tube Cover 

Screw

Tube Cover

Tube Cover 

Screw

TO AVOID A FIRE HAZARD, THE FOAM INSERT 

OVER THE VACUUM TUBES MUST BE REMOVED 

PRIOR TO CONNECTING THE A.C. MAINS POWER 

SUPPLY CORD AND OPERATING THIS PRODUCT.

WARNING

REFER TO PAGE 3 IN THE MC75 OWNER’S 

MANUAL FOR INSTRUCTIONS.

Содержание 60TH ANNIVERSARY SYSTEM - annexe 1

















Отзывы: