background image

14

Specifications

Specifications

Power Output

Minimum sine wave continuous average power output 

is:

75 watts into 2 ohm load

75 watts into 4 ohm load

75 watts into 8 ohm load

Output Load Impedance

2, 4 or 8 ohms

Rated Power Band

20Hz to 20,000Hz

Total Harmonic Distortion

0.5% maximum harmonic distortion at any power 

level from 250 milliwatts to rated power, 20Hz to 

20,000Hz

Frequency Response

+0, -0.5dB from 20Hz to 20,000Hz

+0, -3.0dB from 10Hz to 100,000Hz

Input Sensitivity (for rated output)

1.7 Volt or 0.85 Volt Unbalanced

3.4 Volt or 1.7 Volt Balanced

Signal To Noise Ratio (A-Weighted)

110dB below rated output

Intermodulation Distortion

0.5% maximum, if the instantaneous peak power 

output does not exceed twice the rated power output 

for any combination of frequencies from 20Hz to 

20,000Hz.

Wide Band Damping Factor

Greater than 18

Input Impedance

20,000 ohms Unbalanced

15,000 ohms Balanced

Tube Compliment

1 - 12AX7A Input and Phase Inverter

2 - 12AT7 Voltage Amplifier and Driver

2 - KT88 Power Output

Power Requirements

100V 

50/60Hz at 2.2 Amps

110V 

50/60Hz at 1.8 Amps

120V 

50/60Hz at 1.8 Amps

220V 

50/60Hz at 1.0 Amps

230V 

50/60Hz at 0.9 Amps

240V 

50/60Hz at 0.9 Amps

Standby: 0.5 watt

Note: Refer to the right side panel of the MC75 for the 

correct voltage.

Overall Dimensions

Width is 17-3/4 inches (45.09cm) including Cables

Height is 8-1/2 inches (21.59cm) including feet

Depth is 8-1/2 inches (21.59cm)

Weight

38 pounds (17.24 kg) net, 43.5 pounds (19.73 kg) in 

shipping carton

Shipping Carton Dimensions

Width is 21 inches (53.34cm)

Depth is 13-1/2 inches (34.29cm)

Height is 15-1/8 inches (38.42 cm)

Содержание 60TH ANNIVERSARY SYSTEM - annexe 1

















Отзывы: