background image

2

The lightning flash with arrowhead, within an equilateral 

triangle, is intended to alert the user to the presence of 

uninsulated “dangerous voltage” within the product’s en

-

closure that may be of sufficient magnitude to constitute 

a risk of electric shock to persons.

The exclamation point within an equilateral triangle is 

intended to alert the user to the presence of important 

operating and maintenance (servicing) instructions in the 

literature accompanying the appliance.

WARNING - TO REDUCE RISK 

OF FIRE OR ELECTRICAL 

SHOCK, DO NOT EXPOSE 

THIS EQUIPMENT TO RAIN OR 

MOISTURE.

NO USER-SERVICEABLE PARTS 

INSIDE. REFER SERVICING TO 

QUALIFIED PERSONNEL.

To prevent the risk of electric 

shock, do not remove cover or 

back. No user-serviceable parts 

inside.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install 

in accordance with the manufacturer’s instruc-

tions.

8. Do not install near any heat sources such as 

radiators, heat registers, stoves, or other appa-

ratus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug 

has two blades with one wider than the other. 

A grounding type plug has two blades and a 

third grounding prong. The wide blade or the 

third prong are provided for your safety. If 

the provided plug does not fit into your outlet, 

consult an electrician for replacement of the 

obsolete outlet.

10. Protect the power cord from being walked on 

or pinched particularly at plugs, convenience 

receptacles, and the point where they exit 

from the apparatus.

11. Only use attachments/accessories specified by 

the manufacturer.

12. Use only with the cart, stand, tripod, bracket, 

or table specified by the manu

-

facturer, or sold with the appa-

ratus. When a cart is used, use 

caution when moving the cart/

apparatus combination to avoid 

injury from tip-over.

13. Unplug this apparatus during lightning storms 

or when unused for long periods of time.

14. Refer all servicing to qualified service person

-

nel. Servicing is required when the apparatus 

has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has 

been spilled or objects have fallen into the 

apparatus, the apparatus has been exposed to 

rain or moisture, does not operate normally, or 

has been dropped.

15. Do not expose this equipment to dripping or 

splashing and ensure that no objects filled 

with liquids, such as vases, are placed on the 

equipment.

16. To completely disconnect this equipment from 

the a.c. mains, disconnect the power supply 

cord plug from the a.c. receptacle.

17. The mains plug of the power supply cord shall 

remain readily operable.

18. Do not expose batteries to excessive heat such 

as sunshine, fire or the like.

19. Connect mains power supply cord only to a 

mains socket outlet with a protective earthing 

connection.

IMPORTANT SAFETY 

INSTRUCTIONS!

PLEASE READ THEM BEFORE 

OPERATING THIS EQUIPMENT.

Содержание 60TH ANNIVERSARY SYSTEM - annexe 1

















Отзывы: