manualshive.com logo in svg

McFarlane HDL-100-44 Series, Руководство оператора и инструкции по настройке, Страница: 32 / 55

Поделиться
Скачать
McFarlane HDL-100-44 Series Скачать руководство пользователя страница 32

APPENDIX B

32

HDL-116 through HDL-140 HARROW CART 

PARTS LIST 

Always order by Part Number – 

Not

 by Key Number 

KEY 

PART # 

DESCRIPTION 

QTY. 

1 

PPI-208 

CLEVIS 

1 

2 

PPI-300 

BASE HITCH 

1 

3 

HDL-201 

HITCH POLE – 12’ (116 – 122 models) 

1 

** 

HDL-278 

HITCH POLE – 16’ (124 – 140 models) 

1 

** 
** 
** 

12503 
RT-2021 
RT-3103 

SAFETY CHAIN 
SAFETY CHAIN BUSHING 
SAFETY CHAIN WASHER 

1 
1 
1 

4 

HD-1151 

JACK STAND (10”) 

1 

5 

HDL-227 

MAIN FRAME 

1 

6 

HDL-2540 

CABLE LIFT BRACKET, RT 

1 

** 

HDL-2541 

CABLE LIFT BRACKET, LT 

1 

7 

AL-030 

5/16 SHACKLE 

4 

8 

CH-1406 

1/4 x 6 LINK CHAIN 

2 

9 

HDL-228 

CABLE LIFT ANGLE 

2 

10 

N-021 

LOCK CLIP 

4 

11 

PH-10 

CABLE LIFT ARM SPRING 

2 

12 

HDL-232 

CENTER BAR (132 – 140 models) 

1 

 

HDL-230 

CENTER BAR (118 – 130 models, non-trussed) 

1 

 

HDL-229 

CENTER BAR (116) 

1 

13 

RT-2124 

WING HINGE PIN – 1 1/4 X 7 1/2 

4 

14 

*** 

WING FRAME (note 116 – 130 models are not trussed) 

2 

15 

EB-5808 

EYE BOLT, 5/8 X 8 

2 

16 

HDL-2522 

WING REST 

2 

17 

WDL-2505 

MAIN FRAME AXLE SPINDLE 

2 

18 

HD-1371 

HUB (6-hole hub) 

2 

** 

HD-1360 

GREASE SEAL (6-hole hub) 

2 

** 

HD-1362 

INNER BEARING (6-hole hub) 

2 

** 

HD-1361 

HUB WITH RACES (6-hole hub) 

2 

** 

HD-1363 

OUTER BEARING (6-hole hub) 

2 

** 

HD-1364 

SPINDLE FLAT WASHER (6-hole hub) 

2 

** 

HD-1365 

SPINDLE HEX NUT (6-hole hub) 

2 

** 

CP-1517 

COTTER PIN 

2 

** 

HD-1367 

DUST CAP (6-hole hub) 

2 

19 

11L-15 8T 

MAIN FRAME TIRE 

2 

 

HD-1368 

RIM (15” x 8” 6-hole) for 11L-15 tire 

2 

20 

WC-8xxx 

WING CABLE (HDL-116 AND 118 - NO CABLE) 

2 

21 

HDL-219 

WING CABLE SHACKLE, 5/16 

2 

22 

9.5L-15 8T 

WING FRAME TIRE 

2 

 

HD-1370 

RIM (15” x 6” 6-hole) for 9.5L-15 tire 

2 

23 

HDL-235 

WING CABLE PULL BRACKET, LEFT 

1 

 

HDL-236 

WING CABLE PULL BRACKET, RIGHT 

1 

 

** 

Unnumbered items are not pictured. 

 

 

*** 

Please specify model number when ordering these parts. 

 

 

xxx 

length in inches (84" is 084, 112" is 112) 

 

Содержание HDL-100-44 Series
























































Отзывы:

Нет отзывов