McFarlane HDL-100-44 Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 55

McFarlane HDL-100-44 Series Скачать руководство пользователя страница 23

23

Figure 13

Install the Lighting Package

1.

With the unit in field position, lay out the wire harness wishbone. The wishbone has a four
pin plug in the middle of it and is split with three pin plugs on each end. The three pin plug
connects to the lights. Lay the wishbone out on the tool bar, following across to the first lift
arm of each wing. Do not attach to the frame yet.

2.

Lay out the wire harness extension with the seven pin connector. Start by plugging it into the
wire harness wishbone that is laid out on the tool bar. Work towards the hitch, following
along the center bar tube to the main lift hydraulic cylinder and then along the hydraulic
hoses up to the main frame as shown in the diagram. Do not attach yet. Make sure there is
plenty of slack to connect to the towing vehicle. The wire harness may need to be pulled
towards the hitch and the rear connection point moved to one side.

3.

If the lights are not already mounted into the mounting brackets, attach them now using the
1/4 x 1 1/4 bolts, flat washers, lock washers and hex nuts.

4.

Attach the light assemblies to the first lift arm on the wings using the 3/8 x 2 – 3 ¾ U-Bolts,
lock washers and hex nuts. Do not tighten yet. You may have to adjust the location later. The
lights must be attached so that the red and yellow lens will be facing towards the center of the
unit with the yellow light towards the rear of the unit. The single yellow lens will be facing
away from the center of the unit. Connect the free end of the wishbone to the lights.

«
...
21
22
23
24
25
...
»

Содержание HDL-100-44 Series
























































Отзывы:

Нет отзывов