These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
fi
lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
Installation with a mounting bracket
• Install the laser effect device using a mounting bracket on the ceiling, the wall or on a suitable crossbeam.
When installing it, make sure that the device cannot swing freely.
• Secure the device with fastenings that are compatible with the fastening surface and suitable for carrying
the weight of the light effect device.
• Secure the installation with an additional suitable safety restraint cable or net. The safety restraint cable or
net must be able to support the light effect device in the event of a fault in the main support system.
• Set the desired angle of inclination and tighten the two bracket locking screws well.
Controls and Parts
(1) Microphone
MIC
(2) Laser outlet - Attention, here the laser beam is released
(3) AUTO/MUSIC
Switch
(4) Fan
(5) Functional switch 1-2-3
(6) Connection
DC5V
Connecting the Power Adaptor
The mains socket, to which the laser is connected, must be easily accessible so the
device can be quickly separated from the mains voltage in the case of a fault.
Do not let the mains cable come into contact with other cables.
Be careful when handling the mains cables and main connectors. Mains voltage can
give severe electric shocks, which can be fatal.
Do not leave the cables trailing free; route them in an orderly and professional way to
prevent accidents.
• Plug the enclosed power adaptor‘s low-voltage plug into the DC5V (6) socket on the side of the device.
• Plug the power supply unit into a wall socket.
Operation
• The desired operation mode is selected by means of the functional switch 1-2-3 (5) and the AUTO/MUSIC
(3) switch:
Functional switch 1-2-3 (5)
1
Laser effect with
fl
ashing LED effect
2
Laser effect without LED effect
3
Device is switched off
AUTO/MUSIC Switch (3)
MUSIC
The laser effect is controlled by the beat of the music.
AUTO
The laser effect is now controlled via the integrated controller.
Handling
• Never switch the laser effect device on and off at short intervals. This will considerably reduce the working
life of the device.
• The device is not suitable for continuous use. Pauses in operation increase the working life of the product.
We recommend to let the laser cool down after a two-hour operating time before you put it into operation
again.
• Never switch on the device immediately after it has been taken from a cold into a warm environment. The
condensation that forms might damage your unit.
Allow the device to reach room temperature before switching it on. Wait until the condensation has evapo-
rated.
• To ensure suf
fi
cient ventilation, do not cover the device. In addition, the air circulation must not be
obstructed by objects such as magazines, tablecloths, curtains or similar.
Maintenance
Before cleaning the laser, disconnect it from the power supply (disconnect the power
supply unit).
Make sure that the inside of the device does not get wet or damp.
The outside of the device should be cleaned with a soft, slightly damp cloth or dry brush.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface of the case.
Disposal
Electronic devices are recyclable waste materials and must not be disposed of in the house-
hold
waste!
Please dispose of the product, when it is no longer of use, according to the current statutory
requirements.
Technical Data
Operating voltage (Adaptor)
100-240 V/ 50/60 Hz
Operating voltage (Laser)
5 V DC
Power input
0.2 / 6 W Standby/max.
Laser output
<5 mW
Wavelength
532 / 660 nm
Laser class
3R
Dimensions (without mounting bracket)
160 x 115 x 60 mm
Mass 420
g
Range of operating temperature
+15 to +30 °C
This product complies with the national and European legal requirements.
