background image

28

 -

W

ARRANTY

WHAT DOES THIS WARRANTY COVER?

   MBW, Incorporated (MBW) 

warrants each New Machine against defects in material and workmanship 
for a period of twelve (12) months.  "New Machine" means a machine 
shipped directly from MBW or authorized MBW dealer to the end user. This 
warranty commences on the first day the machine is sold, assigned to a 
rental fleet, or otherwise put to first use.

MBW warrants each Demonstration Machine against defects in material 
and workmanship for a period of six (6) months. "Demonstration Machine" 
means a machine used by MBW or its agents for promotional purposes.  
This warranty commences on the first day the machine is sold, assigned to 
a rental fleet, or otherwise put to first use.

This warranty covers the labor cost for replacement or repair of parts, 
components, or equipment on New Machines or Demonstration Machines, 
and MBW shall pay labor costs at MBW's prevailing rate to affect the 
warranted repair or replacement.  MBW reserves the right to adjust labor 
claims on a claim-by-claim basis.

This warranty covers the shipping cost of replacement parts, components, 
or equipment via common ground carriers from MBW to an authorized 
MBW dealer.  Air freight is considered only in cases where ground 
transportation is not practical.

MAY THIS WARRANTY BE TRANSFERRED?

  This warranty is non-

transferable and only applies to the original end user of a new machine or 
demonstration machine.

WHAT DOES THIS WARRANTY NOT COVER?

1.This warranty does not cover any Used Equipment.  "Used Equipment" 
means any MBW machine or equipment that is not a New Machine or a 
Demonstration Machine.  All Used Equipment is sold 

AS IS/WHERE IS 

WITH ALL FAULTS.

2.This warranty does not cover any New Machine, Demonstration 
Machine, or their equipment, parts, or components altered or modified in 
any way without MBW's prior written consent.  This warranty does not 
cover the use of parts not specifically approved by MBW for use on MBW 
products.  This warranty does not cover misuse, neglect, shipping damage, 
accidents, acts of God, the operation of any New Machine or 
Demonstration Machine in any way other than recommended by MBW in 
accordance with its specifications, or any other circumstances beyond 
MBW's control.  This warranty does not cover any New Machine or 
Demonstration Machine repaired by anyone other than MBW factory 
branches or authorized MBW distributors.

3.This warranty does not cover, and MBW affirmatively disclaims, liability 
for any damage or injury resulting directly or indirectly from design, 
materials, or operation of a New Machine or Demonstration Machine or any 
other MBW product.  MBW's liability with respect to any breach of warranty 
shall be limited to the provisions of this document and in no event shall 
exceed an amount equal to the purchase price of the New Machine or 
Demonstration Machine purchased from MBW.

4.This warranty does not cover engines, motors, and other assemblies or 
components produced by other manufacturers and used on a New 
Machine or Demonstration Machine, as said engines, motors, and other 
assemblies or components may have warranties provided by the 
manufacturer thereof.  This warranty does not apply to consumable items, 
such as v-belts, filters, trowel and screed blades, seals, shock mounts, 
batteries, and the like, all of which are sold AS IS/WHERE IS WITH ALL 
FAULTS.

5.This warranty does not cover the cost of transportation and other 
expenses which may be connected with warranty service but not 
specifically mentioned herein.   

 
6.This warranty does not cover any updates to any New Machine, 
Demonstration Machine, or any other MBW product.  MBW reserves the 
right to improve or make product changes without incurring any obligation 
to update, refit, or install the same on New Machines or Demonstration 
Machines previously sold.

WHAT MUST YOU DO TO OBTAIN WARRANTY COVERAGE?

  Each 

New Machine or Demonstration Machine is accompanied by a Warranty 
Registration Card.  You must sign, date, and return the Warranty 
Registration Card to the place of origin of the New Machine or 
Demonstration Machine, either to MBW, Inc. at P.O. Box 440, Slinger, 
Wisconsin 53086,  MBW (UK), Ltd. at Units 2 & 3 Cochrane Street, Bolton 
BL3  6BN, United Kingdom or MBW FRANCE SARL at 
 ZA D'Outreville, 5 Rue Jean Baptiste Neron, Bornel 60540 France, within 
ten (10) days after purchase, assignment to a rental fleet, or first use.  This 
signed warranty card is the buyer's affirmation that he has read, 
understood, and accepted the warranty at the time of purchase.  Failure to 
return the warranty card as specified herein renders the warranty null and 
void.  In order to receive warranty coverage consideration, warranty claims 
must be submitted within thirty (30) days after the New Machine or 
Demonstration Machine fails.  Warranty claims must be submitted to MBW, 
Inc., MBW (UK), Ltd. or MBW FRANCE SARL, and written authorization for 
the return of merchandise or parts under the warranty must be obtained 
before shipment to MBW.

WHAT WILL MBW DO?

  MBW's obligation under this warranty is limited to 

the replacement or repair of parts for a New Machine or Demonstration 
Machine at MBW factory branches or at authorized MBW distributors, and 
such replacement or repair is the exclusive remedy provided hereunder.  
Labor must be performed at an authorized MBW distributor.   MBW 
reserves the right to inspect and render a final decision on each warranty 
case, and MBW's repair or replacement is solely within the discretion of 
MBW.  

IT IS EXPRESSLY AGREED THAT THIS SHALL BE THE SOLE AND 
EXCLUSIVE REMEDY UNDER THIS WARRANTY.  UNDER NO 
CIRCUMSTANCES SHALL MBW BE LIABLE FOR ANY COSTS, LOSS, 
EXPENSE, DAMAGES, SPECIAL DAMAGES, INCIDENTAL DAMAGES, 
OR PUNITIVE DAMAGES ARISING DIRECTLY OR INDIRECTLY FROM 
THE USE OF THE NEW MACHINE OR DEMONSTRATION MACHINE 
WHETHER BASED UPON WARRANTY, CONTRACT, NEGLIGENCE, 
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY.

THE FOREGOING WARRANTY IS EXPRESSLY IN LIEU OF ALL 
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE 
WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND 
FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER 
OBLIGATIONS OR LIABILITY ON MBW'S PART.  MBW NEITHER 
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME ON 
BEHALF OF MBW ANY OTHER LIABILITY OR WARRANTY IN 
CONNECTION WITH THE SALE OR SERVICE OF ANY NEW MACHINE, 
DEMONSTRATION MACHINE , OR ANY OTHER MBW PRODUCT.

EXTENDED RAMMER WARRANTY - MODELS R422, R442, 
R482 & R483.

This extended warranty commences on the last day of MBW’s standard, 
one year, “limited warranty” and runs for an additional four years
(48 months). This extended warranty is limited to part replacement and 
shipping costs of rammer 

bellows and non-metallic slide bearings only. 

 

This extended warranty does not cover labor, down time, or any other cost 
beyond that of component replacement and freight. This extended 
warranty is subject to all limitations set fourth in MBW’s “limited warranty”, 
above.

Go to

Discount-Equipment.com 

to

order your parts

Содержание MM120


































Отзывы: