MBM 408A Скачать руководство пользователя страница 43

Страница: 43 / 48

7-2 : Troubleshooting

Problem Possible

Cause Countermeasure Reference

Folding
misalignment
occurs.

Fine adjustment is not made.

Correct the misalignment using
the fine adjustment knob.

5.5 Adjustment

The processing speed was changed
during operation.

Do not change the speed during

specified folding operation.

The folding roller is dirty.

Clean the folding roller.

6. Maintenance, Service,
Inspection, Expendables

The paper guides are fixed in the
right angle or not in close contact
with the paper.

Make the paper guide in close
contact with the paper.

The paper feed table is not set in
the right angle.

Straighten the paper feed table
using the slant adjustment knob

5.5.1 Slant adjustment

The paper is cut at a slant.

Correct it using the slant

adjustment knob.

Paper is thin or curled paper is

used.

Replace the paper or (if

possible) turn it over.

Paper jam

frequently occurs.

The folding roller is dirty.

Clean the folding roller

6. Maintenance, Service,
Inspection, Expendables

Folding roller is not properly set. Set the folding roller properly.

Paper out of specification is used. Use a designated paper.

Thicker paper is folded at a slower
speed.

Increase the speed.

5.9 Speed adjustment

The folding tables 1 and 2 are not
properly set.

Set the folding tables 1 and 2
properly.

Some torn paper is stuck at
location where paper passes.

Check where the part is and
remove the foreign paper.

The paper feed roller is dirty.

Clean the paper feed roller.

6. Maintenance, Service,
Inspection, Expendables

Extreme static electricity

Spray commercially available
antistatic spray.

Paper is not fed

even when the
“START” key is
pressed.

There is no paper or only a few

sheets on the paper feed table.

Load the paper on the paper

feed table.

The upper roller or rear cover is
open.

Close the cover.

The paper ejection photo sensor is
dirty.

Clean the paper ejection photo
sensor.

6.5 Cleaning of the paper
ejection photo sensors

Folded paper is
wrinkled.

Paper is coiled around the folder
roller.

Remove the tables 1 and 2 and
remove the paper from the
folding roller.

6.5 Removal and

installation, and cleaning
of folder roller

The folding roller is dirty.

Clean the folding roller.

6. Maintenance, Service,
Inspection, Expendables

Short grain paper is used or paper
is not enough stiffness.

Slow the processing speed.

5.9 Speed adjustment

Paper out of specification is used. Use a designated paper.

Paper is thin or curled paper is

used.

Replace the paper or (if

possible) turn it over(up side
down).

https://www.supplychimp.com

Содержание 408A

















































Результаты поиска

Содержание 408A

Отзывы:

Похожие инструкции для 408A

Бренды по названию

Популярные бренды

MBM 408A, Руководство по эксплуатации

Результаты поиска

Содержание 408A

Отзывы:

Похожие инструкции для 408A

Бренды по названию

Популярные бренды