Maytag W10353871A, Руководство по установке

Страница: 10 / 32

10
USER & SET-UP INSTRUCTIONS
NOTE: After the washer has been installed and plugged in, the
display will show ‘0 MINUTES’. Once the washer has been
plugged in and the washer door opened and closed, the display
will show the price. In washers set for free cycles, the display will
flash ‘SELECT CYCLE’.
1. PD Models: Insert coins until ‘SELECT CYCLE’ flashes
in display.
PR Models: A debit card is required rather than coins. In
Enhanced Debit mode, the card balance will also display
when a debit card is inserted into the reader.
2. Door must be closed before cycle selection is made,
3. Press fabric setting button for the wash cycle desired. After
the cycle is started, the time will display and count down.
4. If a cycle is interrupted by opening the door, ‘RESELECT
CYCLE’ will flash in the display. To restart the washer, close
door, and reselect desired cycle.
General User Information
SCROLLING ‘OUT OF ORDER’ SHOWING IN DISPLAY - This
condition indicates the washer is inoperative.
“0 MINUTES” SHOWING IN DISPLAY - This indicates the cycle is
complete and the washer cannot be operated. Coins dropped or
debit inputs during this condition will be stored in escrow but
cannot be used until normal operation is restored by opening and
closing the door. If a door switch fails, it must be replaced before
normal operation can be restored.
COLD START (Initial first use) - Washer is programmed at the
factory as follows:
WARM START (after power failure) - A few seconds after power
is restored, if a cycle was in progress at the time of the power
failure, ‘RESELECT CYCLE’ will flash in the display, indicating the
need for a key press to restart washer.
DOOR LOCK - Prior to beginning a cycle, there is a door lock
routine of lock/unlock/relock then cycle begins. The door will
remain locked until the end of a cycle or approximately 2 minutes
after a power interruption.
PRICING - After the door is opened following the completion
of a cycle, the display indicates the cycle price (unless set for
free operation). As coins are dropped or debit inputs arrive,
the display will change to lead the user through the initiation
of a cycle.
FREE CYCLES - This is established by setting the cycle price to
zero. When this happens, ‘SELECT CYCLE’ will appear rather
than a cycle price.
DEBIT CARD READY - This washer is debit card ‘cable’ ready. It
will accept a variety of debit card systems, but does NOT come
with a debit card reader. Refer to the debit card reader
manufacturer for proper washer set-up. In models converted
to a Generation 1 debit card system, debit pulses represent
the equivalent of one coin (coin 1).
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
PD Models: Insert service door key, turn, and lift to remove
access door.
PR Models: Once the debit card reader is installed (according
to the reader manufacturer’s instructions), the set-up can be
entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot.
The lower fabric setting buttons and the digital display are used
to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming the washer.
HOW TO USE THE BUTTONS TO PROGRAM THE
CONTROLS
1. PERM PRESS button is used to adjust the
values associated with set-up codes. Pressing the button
will change the value by increments. Rapid adjustment
is possible by holding the button down.
2. DELICATES AND KNITS button will advance through the set-
up codes. Pressing the button will advance to the next
available set-up code. Holding the button down will
automatically advance through the set-up codes at a rate
of 1 per second.
3. QUICK CYCLE button is used to select or deselect options.
Washer 11-minute wash period
3 rinses (extra rinse not enabled)
$1.75 wash price (PD models)
$0.00 wash price (PR models)