Maytag MXR20 Скачать руководство пользователя страница 19

Страница: 19 / 28

Force of Door Seal

If there is a water leakage around the door, the door position may

have shifted and is out of position or the door seal force may need

adjustment. In some cases the door seal needs to be replaced.

Replacing Door Seal

Open the door. Remove the door glass with seal from the door

frame by pushing it towards the drum.

Remove the gasket from the glass.

Place a new seal with a wider groove on the glass, with the

edge up.

Place a smooth cord in the groove, completey encircling the

window. Tighten up the margin by the cord and place the door

glass in the door opening. Hold one end of the cord firmly on the

door. Pull the other cord end towards the center of the glass so

the rubber edge can properly fit into it.

Apply a small amount of silicone RTV between the door frame

and rubber sealing, in the upper and lower parts of the frame.

Make sure the silicone is not pushed over the door seal edge

when the door is closed. Leave the door closed until the silicone

cures.

IMPORTANT:

After replacing the door seal, the door seal pressure

on the door lock side and hinge side may be too high. If this occurs,

run Wash program 1 or Power Wash without any laundry.

Ground Leakage Trips

IMPORTANT:

A qualified technician must perform a ground leakage

trip function test at least once every 3 months.
If the washer is equipped with a ground leakage trip in the inlet

circuit of the electric switchboard, it must be tested regularly. The

ground leakage trip is very sensitive and helps avoid electric shock

during washer operation.

To test:

Press the ground leakage trip test button while the trip is under

tension. If the trip is functioning, it will shut off.

Door Will Not Unlock

In an emergency:

TROUBLESHOOTING

IMPORTANT:

■

Before opening the door, turn off the washer.

■

Do not open the door if the drum has not completely stopped.

■

Do not open the door if “TOO HOT” is displayed.

■

Do not open the door if any part of the washer feels too warm.

■

Do not open the door if there is water in the drum.

Possible Cause

■

A power outage

Solution

■

Make sure it is safe to open the door.

■

Remove front panel.

■

Put your fingers over the edge of the front panel on the door

lock side.

■

First push the emergency door opening button, then turn the

door handle right.

■

Open the door.

Error Message Displayed

Possible Cause

■

See “Fault Code Overview” in Programming Guide.

Solution

■

See “Fault Code Overview” in Programming Guide.

Содержание MXR20




























Результаты поиска

Содержание MXR20

Отзывы:

Maytag MXR20, Руководство по установке, Страница: 19 / 28

Результаты поиска

Содержание MXR20

Отзывы: