Maytag MXR20 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 28

Maytag MXR20 Скачать руководство пользователя страница 14

14

Remove Shipping Brackets

Soft-Mount Models

IMPORTANT:

Shipping brackets must be removed before putting

the washer into service. Failure to do so can cause damage to the

washer. Save the brackets for use if moving the washer in the future.

1.

Remove the front panel and rear panel.

2.

When the washer is lifted off the pallet, make sure the washer

does not come down on the floor with either of the rear corners

first. The side panel can be damaged.

3.

Mount the feet.

4.

Use the feet to level the washer.

5.

Replace both panels.

1 – Front metal shipping brackets
2 – Rear metal shipping brackets
3 – Front panel
4 – Rear panel

Electrical Connection

The power supply of the liquid soap pump system must be

connected to an external electrical source. Only qualified technicians

can make the electrical connection according to local codes.

Instructions for the correct connection can be found on the wiring

diagram located in a plastic bag inside the cabinet. Do not connect

the liquid soap pump system in the washer.

Electronic Controller with MC7 and Graphic Display

PN Models:

For electrical connection of supply control signals,

a plastic box is located on the rear of the washer (see illustration

below, position 1). There is also a terminal box with LED’s that signal

activation of the respective pump (position 3).
A label for electrical connections is located on the back side of the

terminal box cover (see illustration below). Detailed information on

connecting signals can also be found on the electric schematic of the

washer. Signals for the supply pump control are 24V AC. Maximum

current for control circuits of pumps must be limited to 10mA. Insert

the cable for connection of pump control signals through the plastic

cable strain relief (position 2). After connection of conductors to the

respective positions of the connector “P” (screw clamps), attach the

cable by tightening the cable strain relief and replace the cover on

the box. For details about liquid soap supply system programming,

see the Programming Manual.

1

2

3

Electrical Connection Label

Electrical Connection (cont.)

4

2

3

1

Soft-Mount Model Shown

«
...
12
13
14
15
16
...
»

Содержание MXR20





























Отзывы:

Нет отзывов