Maytag MGDE500WR - ADA Compliant, 7.2 Cu Ft Cap, Руководство пользователя

Страница: 9 / 32

9
Changing Cycles, Options, and Modifiers
You can change Sensor Cycles, Timed Cycles, Modifiers, and
Options anytime before pressing START-PAUSE.
NOTE: Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing START-PAUSE
1. Press START-PAUSE once. This pauses the current cycle.
2. Select the desired cycle and options.
3. Press and hold START-PAUSE. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press START-PAUSE within 5 minutes of
selecting the cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start-Pause
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press START-PAUSE once.
2. Select the new Modifier and/or Option.
3. Press and hold START-PAUSE to continue the cycle.
Changing the Preset Sensor Cycles Dryness Settings
If all your loads on all Sensor cycles are consistently not as dry as
you would like, you may change the preset Sensor Cycles Dryness
settings to increase the dryness. This change will affect all of your
Sensor cycles.
Your Sensor Cycles Dryness settings can be adjusted to adapt to
different installations, environmental conditions or personal
preference. There are 3 drying settings: 1 (factory preset dryness
level), 2 (slightly dryer clothes, approximately 15% more drying
time), and 3 (much dryer clothes, approximately 30% more drying
time.)
1. The Sensor Cycles Dryness settings cannot be changed while the
dryer is running.
2. Press and hold the Sensor Cycles Dryness button for 5 seconds.
The dryer will beep, and “ CF” will be displayed on the Estimated
Time Remaining screen for 1 second followed by the current
drying setting.
3. To select a new drying setting, press the Sensor Cycles Dryness
button again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START-PAUSE to save the drying setting.
5. The drying setting you selected will become your new preset
drying setting for all Sensor cycles.
Drying Rack Option
The drying rack is useful for drying items you would not necessarily
want to tumble dry or that you would normally line dry (for example,
sweaters).
If your model does not have a drying rack, you may be able to
purchase one for your model. To find out whether your model allows
drying rack usage and for information on ordering, please refer to the
front page of the manual or contact the dealer from whom you
purchased your dryer.
To use the drying rack
Do not remove the lint screen.
1. Open dryer door.
A
A. Front edge
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on front
edge of drying rack to secure over the lint screen.
A
B
A. Dryer rack front edge
B. Dryer back panel
3. Put the wet items on top of the drying rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the drying rack.
4. Close the door.
5. Select a timed drying cycle and temperature (see following
chart). Items containing foam, rubber, or plastic must be dried on
a clothesline or by using the Air Dry temperature setting.
6. You must select a time by pressing the TIME ADJUST up or down
buttons. Reset time as needed to complete drying. Refer to the
following table.
7. Press and hold START-PAUSE button (about 1 second).
NOTE: Clean the lint screen and remove any lint accumulated from
items dried on the drying rack.