13
■
Plan the installation to use the fewest number of elbows
and turns.
■
When using elbows or making turns, allow as much room
as possible.
■
Bend vent gradually to avoid kinking.
■
Use the fewest 90° turns possible.
Determine vent length an
d
el
b
ows nee
d
e
d
for
b
est
d
rying performance
■
Use the following vent system chart to determine type of vent
material and hood combinations acceptable to use.
NOTE:
Do not use vent runs longer than those specified in the
Vent system chart.
Exhaust systems longer than those specified will:
■
Shorten the life of the dryer.
■
Reduce performance, resulting in longer drying times and
increased energy usage.
The vent system chart provides venting requirements that will help
to achieve the best drying performance.
Vent system chart
NOTE:
Side and bottom exhaust installations have a 90º turn inside
the dryer. To determine maximum exhaust length, add one 90º turn
to the chart.
Num
b
er
90º el
b
ows
Type of vent
Box /louvere
d
hoo
d
s
Angle
d
hoo
d
s
0
Rigi
d
metal
64ft (20 m)
58ft (17.7 m)
1
Rigi
d
metal
54 ft (16.5 m)
48 ft (14.6 m)
2
Rigi
d
metal
44 ft (13.4 m)
38 ft (11.6 m)
3
Rigi
d
metal
35 ft (10.7 m)
29 ft (8.8 m)
4
Rigi
d
metal
27 ft (8.2 m)
21 ft (6.4 m)
Install Vent System
1.
Install exhaust hood. Use caulking compound to seal exterior wall
opening around exhaust hood.
2.
Connect vent to exhaust hood. Vent must fit inside exhaust hood.
Secure vent to exhaust hood with 4" (102 mm) clamp.
3.
Run vent to dryer location. Use the straightest path possible. See
“Determine vent path” in “Plan Vent System.” Avoid 90º turns.
Use clamps to seal all joints. Do not use duct tape, screws, or
other fastening devices that extend into the interior of the vent to
secure vent, because they can catch lint.
INSTALL LEVELING LEGS
WARNING
Excessive Wei
g
ht Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1.
To avoid damaging the floor, use a large flat piece of cardboard
from the dryer carton. Place cardboard under the entire back
edge of the dryer.
2.
Firmly grasp the body of the dryer (not the console panel). Gently
lay the dryer on the cardboard. See illustration.
3.
Examine the leveling legs. Find the diamond marking.
4.
Screw the legs into the leg holes by hand. Use a wrench to finish
turning the legs until the diamond marking is no longer visible.
5.
Place a carton corner post from dryer packaging under each of
the 2 dryer back corners. Stand the dryer up. Slide the dryer on
the corner posts until it is close to its final location. Leave enough
room to connect the exhaust vent.
CONNECT VENT
1.
Using a 4" (102 mm) clamp, connect vent to exhaust outlet in
dryer. If connecting to existing vent, make sure the vent is clean.
The dryer vent must fit over the dryer exhaust outlet and inside the
exhaust hood. Check that the vent is secured to exhaust hood
with a 4" (102 mm) clamp.
2.
Move dryer into its final location. Do not crush or kink vent.
3.
(On gas models) Check that there are no kinks in the flexible
gas line.
4.
Once the exhaust vent connection is made, remove the corner
posts and cardboard.
CONNECT INLET HOSE
(STEAM MODELS)
The dryer must be connected to the cold water faucet using the new
inlet hoses. Do not use old hoses.
1.
Turn cold water faucet off and remove washer inlet hose.
2.
Remove old rubber washer from inlet hose and replace with new
rubber washer provided. If space permits, attach the brass female
end of the “Y” connector to the cold water faucet.
NOTE:
If “Y” connector can be attached directly to cold water
faucet, go to Step 6. If “Y” connector cannot be attached
directly to the cold water faucet, the short hose must be used.
Continue with Step 3.
3.
Attach short hose to cold water faucet. Screw on coupling by
hand until it is seated on faucet.
