background image

3

 

WARNING:

FIRE OR EXPLOSION HAZARD 
Failure to follow safety warnings exactly could result in serious injury, death, or property 
damage.
  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 
  or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s 

instructions.

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified installer, service agency, or 

the gas supplier.

Clear the room, building, or area of all occupants.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas 

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National 

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.

In the State of Massachusetts, the following installation instructions apply:

■  

Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by 

the State of Massachusetts.

■  

Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■  

A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

Содержание MGDB835DW4



























Отзывы: