background image

5

4. On Ranges Equipped with Storage Drawers:

Remove the storage drawer. Use a ¼" drive ratchet to lower 
the rear leveling legs one-half turn. Use a wrench or pliers to 
lower front leveling legs one-half turn.

On Ranges Equipped with Warming Drawers:

Use wrench or pliers to lower the front and rear leveling legs 
one-half turn.

Install Anti-Tip Bracket

Contact a qualified floor covering installer for the best procedure 
for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard 
or hardboard.

1. Remove template from the anti-tip bracket kit (found inside 

the oven cavity) or from the back of this manual.

2. Place template on the floor in cabinet opening so that the left 

edge is against cabinet and top edge is against rear wall, 
molding or cabinet.

3. Tape template into place.

4. If countertop is not flush with cabinet opening edge, align 

template with overhang.

If cabinet opening is wider than that specified in the “Location 
Requirements” section, adjust template so range will be 
centered in cabinet opening.

5. To mount anti-tip bracket to wood floor, drill two 

¹⁄₈

" (3.2 mm) 

holes at the positions marked on the bracket template. 
Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a 

³⁄₁₆

" (4.8 mm) masonry drill bit to drill 2 holes at the positions 

marked on the bracket template. Remove template from floor. 
Tap plastic anchors into holes with a hammer.

6. Align anti-tip bracket holes with holes in floor. Fasten anti-tip 

bracket with screws provided.

Depending on the thickness of your flooring, longer screws 
may be necessary to anchor the bracket to the subfloor. 
Longer screws are available from your local hardware store.

7. Move range close enough to opening to allow for electrical 

connections to be made. Remove shipping base, cardboard 
or hardboard from under range. 

8. Make electrical connections as described in the “Electrical 

Connection” section.

A. ¼" drive ratchet
B. Rear leveling leg

C. Wrench or pliers
D. Front leveling leg

A. Rear leveling leg
B. Front leveling leg

C. Wrench or pliers

A

B

C

D

A

B

C

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death 
or serious burns to children and adults.

Содержание MER7662WQ - Ceramic Range













Отзывы: