background image

7

5.

 

Select the desired cycle

Select the desired cycle for your load. See the “Cycle Guide” 

for more information about each cycle. 

NOTE: 

Most loads may be dried using the Normal dryness 

level, which is shown in bold letters on the control panel. 

Normal is the energy preferred dryness level and will use  

the least energy.

6.

  

Press START to begin cycle

Press and hold the START button to begin the cycle.

To stop your dryer at any time:

Turn the Cycle Control knob to the STOP position or open  

the door.

To restart the dryer:

1.

  Close the door.

2.

  Select a new cycle and temperature (if desired). 

3.

  After the beep sounds, press the START button. 

To change the cycle or temperature after pressing 

START:

1.

  Open the dryer door.

2.

  Press the TEMPERATURE button to change the  

temperature (if desired).

3.

  Turn the cycle knob to the new desired position.

4.

  After the beep sounds, press the START button.

DRYER CARE

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would 

block the air flow for proper dryer operation. This includes 

clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum
1.

  Use a mild hand dish detergent mixed at a low 

concentration with very warm water, and rub with  

a soft cloth.

2.

  Rinse well with a wet sponge or towel. 

3.

  Tumble a load of clean clothes or towels to dry drum 

 OR 
  Use a microfiber cloth and hot water in a spray bottle  

to clean the drum and a second microfiber towel to dry.

NOTE:

 Garments that contain unstable dyes, such as 

denim blue jeans or brightly colored cotton items, may 

discolor the rear of the dryer interior. These stains are  

not harmful to your dryer and will not stain future loads  

of clothes. Dry unstable dye items inside out to avoid 

transfer of dye.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, 

depending on dryer usage. Cleaning should be done by a 

qualified appliance servicer or ventilation system cleaner.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, 

depending on dryer usage.

Содержание MED7500YW





























Отзывы: