background image

22

First try the solutions suggested here or visit our website at www.maytag.com/help  

for assistance and to possibly avoid a service call.  

If you experience

Possible Causes

Solution

Door not closed completely.

Make sure the dryer door is closed completely.

Press and hold the START button 2–5 seconds.

Household fuse is blown or circuit 

breaker has tripped.

There may be 2 household fuses or circuit breakers for the 

dryer. Check that both fuses are intact and tight, or that both 

circuit breakers have not tripped. Replace the fuses or reset the 

circuit breaker. If the problem continues, call an electrician.

TROUBLESHOOTING

Dryer will not run

Unusual Noise

START button not pressed firmly or 

held long enough.

Dryer Operation

Incorrect power supply.

Electric dryers require 240-volt power supply.  

Check with a qualified electrician.

Wrong type of fuse.

Use a time-delay fuse.

Thumping noise

Dryer hasn’t been used in a while.

This is normal. The thumping sound should diminish after a few 

minutes of use.

Rattling or vibrating 

noise

A small object caught between the 

edges of dryer drum.

Check the front and rear edges of the drum for small objects. 

Clean out pockets before laundering.

Dryer isn’t properly leveled.

The dryer may vibrate if not properly installed. See “Level 

Dryer.” All four dryer feet should be in firm contact with the 

floor.

Clothing is balled up in dryer.

When balled up, the load will bounce, causing the dryer to 

vibrate. Separate the load items and restart the dryer.

Dryer will not heat

Household fuse is blown or circuit 

breaker has tripped.

The drum may be turning, but you may not have heat. Electric 

dryers use 2 household fuses or circuit breakers. Replace the 

fuses or reset the circuit breaker. If the problem continues, call 

an electrician.

Incorrect power supply.

Electric dryers require 240-volt power supply.  

Check with a qualified electrician.

Содержание MED7500YW





























Отзывы: