112204 - 6
Maytag Co.
17
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical
shock.
NOTE:
To prevent damage, avoid cleaning and/or touching
ignitor/flame-probe assembly.
Remove lint from gas valve burner area with a dusting brush
or vacuum cleaner attachment.
Non-Coin Models
Microprocessor Controller (Computer)
The L.C.D. display reads “SELECT CYCLE” (no cycle in
progress).
Scroll up or down to the desired cycle using the “
▲
” or “
▼
”
arrow key. Press the “
✓
” key and the highlighted cycle will
start (tumbler, blower, then the heat).
The L.C.D. display will read the name of the selected cycle
and the approximate remaining minutes.
NOTE:
The dryer can be paused or stopped at any time.
Press the “X” key (Pause/Stop) once to pause the cycle.
Press the “
✓
” key to restart the cycle, or press the “X” key
again to cancel the cycle in progress and return to the
“SELECT CYCLE” state. If nothing is done, the cycle will
restart automatically in 20 seconds.
When the programmed drying time has expired, the computer
will proceed into the Cool Down part of the cycle. The L.C.D.
display will read “COOL DOWN” and the remaining minutes.
During the cycle, the dryer will shut off the heat and continue
the fan and tumbler until the Cool Down Time or
Temperature has been reached.
At the end of the cycle the L.C.D. display will read “Cycle
Done”. Opening the main door will put the computer back
into the “Select Cycle” state.
Shutdown Instructions _______________
If the dryer is to be shutdown (taken out of service) for a
period of time, the following must be performed:
Discontinue power to the dryer either at the external
disconnect switch or the circuit breaker.
Discontinue the fuel supply: close external gas shutoff valve.
Also close internal gas shutoff valves.
PN models only, disconnect the hose to the S.A.F.E. system.
Unscrew the 3/4” 11.5 NH hose adapter to the 3/8” N.P.T.
water connection located at the upper rear of the dryer as
well as the coupling seated on the supply valve.
Service / Parts Information __________
Service
Service must be performed by a qualified trained technician,
service agency, or gas supplier. If service is required, contact
the Maytag distributor from whom the equipment was
purchased. If the distributor cannot be contacted or is
unknown, contact the Maytag Co. for a distributor in your
area.
NOTE:
When contacting the Maytag Co., ensure to give
the correct model number and serial number so that your
inquiry is handled in an expeditious manner.
Parts
Replacement parts should be purchased from the distributor
from whom the Maytag equipment was purchased. If the
distributor cannot be contacted or is unknown, contact
the Maytag Co. for a distributor in your area or visit:
www.maytagcommerciallaundry.com and click on distributor
locator.
NOTE:
When ordering replacement parts from the Maytag
distributor or the Maytag Co. be sure to give them the
correct model number and serial number so that your parts
order can be processed in an expeditious manner.
Routine Maintenance _________________
Cleaning
A program and/or schedule should be established for periodic
inspection, cleaning, and removal of lint from various areas
of the dryer, as well as throughout the ductwork system. The
frequency of cleaning can best be determined from
experience at each location. Maximum operating efficiency
is dependent upon proper airflow. The accumulation of lint
can restrict this airflow.
NOTE:
Suggested time intervals shown are for average
usage, which is considered 6 to 8 operational (running)
hours per day.
Every 6 months, inspect the exhaust ducting and remove
any lint buildup.
Suggested Cleaning Schedule
Every Third or Fourth Load
Clean the lint screen every third or fourth load. A clogged lint
screen will cause poor dryer performance. The lint door/
drawer is located just below the loading door of the dryer.
Open the lint drawer, brush the lint off the lint screen, and
remove the lint. Inspect lint screen and replace if torn.
NOTE:
To remove the lint drawer from the dryer, pull the
drawer out loosen the torx screws on the sides of the rails.
This allows the metal clips to rotate and allow the drawer to
be fully removed. Reverse the above process for
installation.
IMPORTANT:
The frequency of cleaning the lint screen
can best be determined from experience at each location.
Weekly
Clean lint accumulation from lint chamber, thermostat, and
microprocessor temperature sensor area.
90 Days
!
WARNING
