background image

3

WARNING

Changes or modifications not expressly approved by the par

-

ty responsible for compliance could void the user’s authori

-

ty to operate the equipment.

SAFETY  CONSIDERATIONS

IMPORTANT NOTE: This unit is designed to 

meet the NOx requirement of 14Ng/J maximum 

as required by the South Coast Air Quality 

Management District and the San Joaquin Valley 

Air Pollution Control District, both in the State 

of California, and is intended for installation in 

those districts only.

This unit has a control system that compensates for certain 

installation and environmental conditions. This unit must:

•   Be properly installed, operated, and maintained per 

the instructions.

•   Be serviced only by properly trained service 

technicians.

Units that are not installed, maintained, or operated 

properly may result in “noisy” operation during the heating 

cycle. If this unit is making unusual or objectionable noises 

during the heating cycle, turn the heat off at the thermostat 

and contact a qualified service organization right away.

Adhere to the following warnings and cautions when 

installing, adjusting, altering, servicing, or operating the 

furnace. To ensure proper installation and operation, 

thoroughly read this manual for specifics pertaining to the 

installation and application of this product.

This furnace is manufactured for use with natural gas only. 

Install this furnace only in a location and position 

as specified in 

LOCATION REQUIREMENTS & 

CONSIDERATIONS

 section and 

INSTALLATION 

POSITIONS

 section of this manual.

Provide adequate combustion and ventilation air to the 

furnace as specified in 

COMBUSTION & VENTILATION 

AIR REQUIREMENTS

 section of this manual.

Combustion products must be discharged to the outdoors. 

Connect this furnace to an approved vent system only, as 

specified in 

VENT/FLUE PIPE & COMBUSTION AIR PIPE

 

section of this manual.

Never test for gas leaks with an open flame. Use a 

commercially available soap solution made specifically for 

the detection of leaks to check all connections, as specified 

in 

GAS SUPPLY AND PIPING

 section of this manual.

Always install a furnace to operate within the furnace’s 

intended temperature-rise range with a duct system which 

has external static pressure within the allowable range, 

as specified on the furnace rating plate and Operational 

Checks section of these instructions.

When a furnace is installed so that supply ducts carry 

air circulated by the furnace to areas outside the space 

containing the furnace, the return air shall also be handled 

by duct(s) sealed to the furnace casing and terminating 

outside the space containing the furnace.

A gas-fired furnace for installation in a residential 

garage must be installed as specified in the 

LOCATION 

REQUIREMENTS AND CONSIDERATIONS

 section of this 

manual.

This furnace cannot be used as a construction site heater.

CAUTION

FROZEN AND BURST WATER PIPE HAZARD 

Failure to protect against the risk of freezing may result in 

property damage. 

Special precautions MUST be made if installing furnace 

in an area which may drop below freezing. This can cause 

improper operation or damage to equipment. If the furnace 

environment has the potential of freezing, the drain trap 

and drain line must be protected. The use of accessory drain 

trap heaters, electric heat tape and/or RV antifreeze is rec

-

ommended for these installations. 

WARNING

To prevent personal injury or death due to improper instal

-

lation, adjustment, alteration, service or maintenance, refer 

to this manual. For additional assistance or information, 

consult a qualified installer, servicer agency or the gas 

supplier. 

Содержание Amana MVS96 Series













































Отзывы: