background image

4

3.

Loosen set screws on wired terminals labeled
REMOTE and insert wires into the openings. Tighten
set screws. (See following figure for switch connection)

4.

Connect wires at door switch.

Jumper Placement 
Description

Jumper in position 
for external power

BATTERY POWERED

NOTE:

 For battery powered, the 2 jumpers must be

positioned on the center and left pins. See jumper pin location
in photo above.

POWERED CONNECTION

NOTE: 

For external power connection, the 2 jumpers must

be positioned on the center and right pins. See jumper
location in photo above.

External Power 
Connections

Wired Door Switch 
Connections

Mounting Sensor/Door Magnet Installation

for DD01E and DD01F Kits

DD01E and DD01F must be mounted on the top door frame
as close to the door as possible in the horizontal position.

A DT01* must be installed in the PTAC unit for the DD01E
or DD01F to be operable.

Skip these steps if not installing.

1. Remove motion sensor from mounting plate by pulling

apart.

2. Mount the back plate on the door trim directly above

the door using the enclosed screws.  (Position so the
UP arrow is pointing up.) Mount the DD01E as low as
possible on the door frame to be as close to the moving
part of the door as possible without interfering with
the door opening or closing.  Choose a location for
mounting the back plate that will provide good coverage
of the PIR for motion into the room. Make sure that
the DD01E will not interfere with the normal opening
and closing of the door.

DO NOT SNAP MOTION SENSOR IN PLACE UNTIL AFTER

BINDING PROCESS.

See Binding Instructions, page 10.

DOOR

DOOR TRIM

DD01*

DD01E and DD01F Mounting

3. Install two (2) AA batteries (included) into the back of

the sensor. Terminals are marked “+” and “-” for
polarity.

 Do NOT put batteries into the device until

AFTER the magnet location is selected to test.

Содержание Amana DD01E

















Отзывы: