manualshive.com logo in svg

MAYSER RADIOBAND 3G, Руководство пользователя, Страница: 2 / 24

Поделиться
Скачать
MAYSER RADIOBAND 3G Скачать руководство пользователя страница 2

Index

Important safety instructions.............................................................3

System usage.......................................................................................................3

INTRODUCTION..............................................................................4

Function..............................................................................................................4
Receiver RB3 R868  ............................................................................................5
RB3 T868 transmitter...........................................................................................6

INSPECTION AND MAINTENANCE...................................................7

1 Connect devices.................................................................................................7
2 Connect the receiver to the motor control.............................................................9

2.1   Setting the receivers / operating modes..................................................................10
2.2   ATEST Signal........................................................................................................11

3 Connect the safety edge to the transmitter (connection examples)………………….12

PROGRAMMING………………………………………………………..…13

4

 Programming..........................................................................................13

4.1   MODE 1: Safety edge connected to IN1 activates R1...............................................14
4.2   MODE 2: Safety edge connected to IN1 activates R2...............................................15
4.3   MODE 3: Safety edge connected to IN1 activates R1 and R2....................................16
4.4   MODE 4: Safety edge connected to IN1 activates R1 and safety edge connected to IN2 
activates R2.................................................................................................................17

CHECKING AND MAINTENANCE....................................................18

5 

Does the equipment work properly?...........................................................18

6 

CHECK function   ...................................................................................19

7 

Troubleshooting.......................................................................................20

8 

Total reset...............................................................................................21

9 

Batteries  ...............................................................................................21

Technical data summary......................................................................................22

EU Declaration of conformity...............................................................................24

UM_320XXXX_RB3SYSTEM_EN_MAYSER_Rev00                                                                                       Página 2/24

Содержание RADIOBAND 3G

























Отзывы:

Нет отзывов