Installation and Operational Instructions for ROBA
®
-diskstop
®
Type 894.5_ _._ _ Sizes 9 and 10
(B.8.4.5.EN)
27/08/2020 TL/GC/SU
Chr. Mayr GmbH + Co. KG
Eichenstraße 1, D-87665 Mauerstetten, Germany
Phone: +49 8341 804-0, Fax: +49 8341 804-421
Page 2 of 17
Safety and Guideline Signs
DANGER
Immediate and impending danger, which can
lead to severe physical injuries or to death.
ATTENTION
Possible property damage can be the
consequence.
Please Observe!
Guidelines on important points
Approvals
EU Type Examination Certificate (Elevator Directive):
EU-BD 1075
for Size 9
EU-BD 1030
for Size 10
Guidelines on the Declaration of Conformity
A conformity evaluation has been carried out for the product (electromagnetic safety brake) in terms of the EU Low
Voltage Directive 2014/35/EU and RoHS 2011/65/EU with 2015/863/EU. The Declaration of Conformity is laid out in
writing in a separate document and can be requested if required.
Guidelines on the EMC Directive 2014/30/EU
The product cannot be operated independently according to the EMC Directive.
Due to their passive state, brakes are
also
non-critical equipment according to the EMC.
Only after integration of the product into an overall system can this be evaluated in terms of the EMC.
For electronic equipment, the evaluation has been verified for the individual product in laboratory conditions, but not in the
overall system.
Guidelines on the Machinery Directive 2006/42/EC
The product
is a component for installation into machines according to the Machinery Directive 2006/42/EC.
The brakes can fulfil the specifications for safety-related applications in coordination with other elements.
The type and scope of the required measures result from the machine risk analysis. The brake then becomes a machine
component and the machine manufacturer assesses the conformity of the safety device to the directive.
It is forbidden to start use of the product until you have ensured that the machine accords with the regulations stated in the
directive.
Guidelines on the EU Directive 2011/65/EU (RoHS II) with 2015/863/EU (RoHS III
– from 22 July 2019)
These
restrict
the use of certain hazardous substances in electrical and electronic devices as well as in products /
components (category 11), the proper operation of which is dependent on electric currents and electromagnetic fields.
Our electromagnetic products / components fulfil the requirements laid down in the RoHS Directive(s), taking into
account the valid exceptions (according to Appendix III and IV RoHS (2011/65/EU) with delegated Directives (EU)
2018/739-741 from 01.03.2018 for Category 11
– until 21 July 2024) and comply with the RoHS.
Guidelines on the ATEX Directive
Without a conformity evaluation, this product is not suitable for use in areas where there is a high danger of explosion.
For application of this product in areas where there is a high danger of explosion, it must be classified and marked
according to Directive 2014/34/EU.
Guidelines on the REACH Regulation (EC) No. 1907/2006
of the European Parliament and of the Council Concerning the Registration, Evaluation, Authorisation and Restriction of
Chemicals. This regulates the manufacture, placing on the market and use of chemical substances in preparations, under
certain conditions also pertaining to substances in products.
mayr
®
power transmission exclusively manufactures
products (articles: clutches/couplings, electric motors, brakes and the appropriate rectifiers) in accordance with the
definition in Article 3 Section 3 of the REACH Regulation. In some products (ROBA-stop
®
, Sizes 2
– 11, Type 8 - -.- - -.- /
ROBA-stop
®
-M, Sizes 2
– 500, Type 891.- - -.- / ROBA-stop
®
-silenzio
®
, Sizes 4
– 8, Type 896.- - -.- - / ROBA
®
-topstop
®
,
Sizes 100
– 260, Type 899.- - -.- -), shoulder screws are installed which are made from a copper alloy containing up to
2.5 % by weight lead. Products made from copper and copper alloys do not fall within the area of applicability of
Regulation (EC) No. 1272/2008 of the European Parliament and Council Concerning the Classification, Labelling and
Packaging of Substances and Mixtures (CLP Regulation) and are therefore not subject to the classification and labelling
obligations. We would hereby like to point out that the proportion of lead used here is not prohibited according to the
REACH Regulation. It is merely necessary to declare the use of this substance.
CAUTION
Danger of injury to personnel and damage to
machines.
