maxxess eMAX-MR62e Скачать руководство пользователя

Страница: 13 / 16

February, 2019

eMAX-MR62e-Man

Page 13 of 16

Appendix A - Configuring the eMAX-MR62e

The eMAX-MR62e local controllers include an internal web page for configuring the communication
parameters of the device. It is recommended that the device be preconfigured in a controlled
environment before installing the device on site.

Default IP is 192.168.0.251
Default user and password is

admin

and

password

Configuration of the eMAX-MR62e controller requires the following information.

•

IP Address

_____.______.______._____

•

Subnet Mask _____.______.______._____

•

Gateway IP

_____.______.______._____

Connecting to the eMAX-MR62e local controller

1. Connect the device to a computer using a standard network cable.

2. Set the computer

’s IP to a Statis IP Address of 192.168.0.10.

3. At the eMAX-MR62e Module, be sure to turn dipswitch #1 to the ON position. This enables the use of

the DEFAULT Login credentials, and will time out in 5 minutes.

4. Connect to the device from your browser using

http://192.168.0.251

. The following screens will

appear.

This message may be different, depending on the version of Operating System that you have installed.

First Click on

“ Details “, which will tell you that your PC does not recognize the Web Pages’s Security

Certificate. This is Normal. Then click on

“ Go on to the webpage “.

Содержание eMAX-MR62e

















Результаты поиска

Содержание eMAX-MR62e

Отзывы:

Похожие инструкции для eMAX-MR62e

Бренды по названию

Популярные бренды

maxxess eMAX-MR62e, Инструкция по установке и технические характеристики

Результаты поиска

Содержание eMAX-MR62e

Отзывы:

Похожие инструкции для eMAX-MR62e

Бренды по названию

Популярные бренды