Maxton EMV10 Скачать руководство пользователя страница 53

Страница: 53 / 102

1728 Orbit Way - Minden, Nevada 89423 P: 775-782-1700 F: 775-782-1701 [email protected] www.maxtonvalve.com

\\SERVER\CATALOG 2019\2019 Catalog Rev 2

ADJUSTMENT PROCEDURE UC4MR

B44

THE INFORMATION PRESENTED HEREIN IS FOR USE BY SKILLED HYDRAULIC ELEVATOR PROFESSIONALS

SPECIAL CONSIDERATIONS:

Make all adjustments at minimum pressure (no load on elevator) except where noted. “IN” is ALWAYS (CW) clockwise. “OUT” is ALWAYS (CCW)

counterclockwise.

THE CONTROL PLATE ADJUSTERS HAVE SEAL NUTS, NOT LOCK NUTS.

Adjust nut only to set seal friction (friction will

maintain adjustment). When adjustment procedure calls for coils to be disconnected, disconnect them electrically. Do not remove them physically.

Make adjustments with a minimum oil temperature of 80˚ F, not to exceed 100˚ F maximum. Maxton recommends the use of a 5 micron filtration

system. With the presence of at least some adverse conditions in most installations, serious consideration should be given to overhaul or

replacement of a control valve on a five year cycle.

GAUGE PORTS:

Gauge ports - 1/8” NPT provided at points A, B and S.

Port: Pump pressure (RELIEF, WORKING PRESSURE).

Port: Jack pressure (STATIC, DOWN RUNNING).

Port: Low pressure switch port.

Note: The minimum operating pressure at port B should be at

least 175 psi (12 bar) as car is moving down full speed with no

load. See flow chart.

OPERATIONAL DATA:

Min. / Max. Pressure:

Max. Rated Flow:

Operating Temperature:

Optimal Temp. Range.

Oil Type:

175-800 psi (3.4-55 bar)

185 gpm (700 l / min.)

80˚-150˚ F (26˚- 65˚ C)

100˚-130˚ F (38˚- 54˚ C)

Hyd. ISO VG 32

150 SUS @ 100˚ F (38˚ C)

* SAFETACH2

performance meter validates valve adjustment by providing

direct speed and acceleration (g-force) readouts.

Questions:

Call Tech Support (775) 782-1700 (7am-4pm PST), use

Maxtonvalve.com or download Maxton Mobile Mechanic from your APP Store

BPS

Disconnect the

coil, turn

IN (CW) register an up call and

turn

BPS

IN (CW) until the car just moves. Next, turn the

BPS

adjuster OUT (CCW) until it stops the movement of the car, then

OUT 1/ 2 turn more. Snug lock nut on

BPS

adjuster and stop

pump. NOTE: If car does not move with

BPS

fully IN (CW), the

valve may be oversized for the job (consult factory for proper valve

sizing). Reconnect the

coil.

coils energized, car should

not move), slowly turn

OUT (CCW) to attain

full up speed within 24 to 36 inches.

(Accel 0.04g-0.09g).

Disconnect the

coil. Turn

adjuster IN (CW) to stop and

readjust

LS*

). Turn

adjuster OUT (CCW) to attain 9 to 12 fpm

leveling speed. Reconnect the

coil and lower the car to lowest

landing.

*(Read leveling speed)

IN (CW) so that the car slows to

provide 4 to 6 inches of stabilized up leveling. Repeat steps 3 and

4 as necessary.

*(Decel 0.04g-0.09g)

With

adjuster fully OUT (CCW), car should stop 1/4" to 3/8"

below floor. After a normal up run, turn

IN (CW) as needed to

bring car to floor level. The pump must be timed to run ½ second

after the car has reached the floor.

With empty car at bottom floor, disconnect

coils and

BPS

and

LS*

Dot on the

adjuster should be referenced to the line between

F / S. When necessary, disconnect the

coil and

turn the

adjuster

IN (CW) to stop. Unlock the LS adjuster by loosening the screw next

to the symbol 1 turn. Move the

adjuster slightly toward S for

slower or F for faster leveling speeds. Set adjustment from 3 to 5 fpm

with the

adjuster, tighten locking screw down, verify LS speed after

tightening screw, then repeat step 3.

* (Level Speed Test 3 to 5 fpm).

DSR

OUT (CCW) until the car

reaches approx. 5% above contract speed. NOTE: You may

need to turn

IN (CW) until the car begins down acceleration.

In order to achieve desired speed,

may need to be turn OUT

(CCW).

adjuster (CW slower). Tighten the lock nut (snug) & send car to

upper landing.

*(Read high speed).

Disconnect

coil. Register a down call and set down leveling

speed at 6 to 9 fpm with the

adjuster. Tighten the lock nut

(snug tight). Reconnect

coil.

* (leveling speed 6 to 9 fpm).

IN (CW) so that the car slows to

provide 4 to 6 inches of stabilized down leveling. NOTE: A minor

re-adjustment of

may be necessary. Send car to upper

landing.

* (Decel 0.04g-0.09g).

Turn

IN (CW) until desired rate of acceleration is achieved.

Full down speed should be attained within 24 to 36 inches.

(Accel 0.04-0.09g).

MANUAL LOWERING:

Push

button to lower car downward

at leveling speed when necessary

RELIEF:

Land car in pit and install pressure gauge in

port.

Turn

and

RELIEF

adjuster OUT (CCW) to stop.

Close the manual shut off valve to the jack.

RELIEF

IN (CW) to increase pressure. Final setting

should be in accordance with local code requirement not

to exceed 150% of maximum operating pressure.

Tighten the lock nut (snug).

Restart to check the pressure relief setting. Seal as
required .

Open the manual shut off valve to the jack.

Readjust

for proper Up Acceleration

*(Accel 0.04g-0.09g)

DEFAULT SETTINGS

If valve is received from Maxton, only minor adjustments may be required.

CONTROL PLATE

UP STOP

OUT

(CCW)

to stop

(faster rate)

UP LEVEL

(CW)

to stop

(slower rate)

UP ACCELERATION

(CW)

to stop

(slower rate)

UP TRANSITION

OUT

(CCW)

to stop

(faster rate)

VALVE BODY

BPS

BY-PASS SIZING

OUT

(CCW)

to stop

(delays up start)

LEVEL SPEED (factory set) DOT ON LINE

(set 3-5 fpm)

RELIEF APPROX 450 psi (CW increases pressure)

DEFAULT SETTINGS

If valve is received from Maxton, only minor adjustments may be required.

CONTROL PLATE

DOWN TRANSITION

OUT

(CCW)

to stop

(faster rate)

DOWN ACCELERATION

OUT

(CCW)

to stop

(faster rate)

MANUAL LOWERING

VALVE BODY

DOWN SPEED Turn OUT (CCW) 9 threads above lock nut.

(faster speed)

DOWN LEVEL Turn OUT (CCW) 2 threads above lock nut.

(faster speed)

Push Button

DSR DOWN SPEED REGULATOR Turn IN (CW) 1 thread above jam nut

Содержание EMV10







































































































Результаты поиска

Содержание EMV10

Отзывы:

Бренды по названию

Популярные бренды

Maxton EMV10, Руководство пользователя

Результаты поиска

Содержание EMV10

Отзывы:

Бренды по названию

Популярные бренды