Maxton EMV10 Скачать руководство пользователя страница 17

Страница: 17 / 102

1728 Orbit Way - Minden, Nevada 89423 P: 775-782-1700 F: 775-782-1701 [email protected] www.maxtonvalve.com

\\SERVER\CATALOG 2019\2019 Catalog Rev 2

THE INFORMATION PRESENTED HEREIN IS FOR USE BY SKILLED HYDRAULIC ELEVATOR PROFESSIONALS

SPECIAL CONSIDERATIONS:

Make all adjustments at minimum pressure (no load on elevator) except where noted. “IN” is ALWAYS (CW) clockwise. “OUT” is ALWAYS (CCW)

counterclockwise.

THE CONTROL BLOCK ADJUSTERS HAVE SEAL NUTS, NOT LOCK NUTS.

Adjust nut only to set seal friction (friction will maintain

adjustment). When adjustment procedure calls for coils to be disconnected, disconnect them electrically. Do not remove them physically. Make adjustments

with a minimum oil temperature of 80˚ F, not to exceed 100˚ F maximum. Maxton recommends the use of a 5-micron filtration system. With the presence of at

least some adverse conditions in most installations, serious consideration should be given to overhaul or replacement of a control valve on a five year cycle.

GAUGE PORTS:

Gauge ports - 1/8” NPT provided at points A, B and S.

Port: Pump pressure (RELIEF, WORKING PRESSURE).

Port: Jack pressure (STATIC, DOWN RUNNING).

Port: Low pressure switch port.

Note: The minimum operating pressure at port B should be at least 50 psi

(3.4 bar) as car is moving down full speed with no load. See flow chart.

OPERATIONAL DATA:

Min. / Max. Pressure:

Max. Rated Flow:

Operating Temperature:

Optimal Temp. Range.

Oil Type:

50-600 psi (3.4-41.5 bar)

360 gpm (1363 l / min.)

80˚-150˚ F (26˚-65˚ C)

100˚-130˚ F (38˚-54˚ C)

Hyd. ISO VG 32

150 SUS @ 100˚ F (38˚ C)

* SAFETACH2

performance meter validates valve adjustment by providing direct

speed and acceleration (g-force) readouts.

Questions:

Call Tech Support (775) 782-1700 (7am-4pm PST), use

Maxtonvalve.com or download Maxton Mobile Mechanic from your APP Store

ADJUSTMENT PROCEDURE UC1, UC1A, UC2, UC2A

B44

DEFAULT SETTINGS

If valve is received from Maxton, only minor adjustments may be required.

CONTROL BLOCK

UP STOP

OUT

(CCW)

to stop.

(faster rate).

UP LEVEL

(CW)

to stop.

(slower speed).

UP ACCELERATION

(CW)

to stop.

(slower rate).

UP TRANSITION

OUT

(CCW)

to stop.

(faster rate).

RELIEF (factory set)

APPROX 450 psi (CW increases pressure)

VALVE BODY

BPS

BY-PASS SIZING

OUT

(CCW)

to stop

(delays up start)

LS*

LEVEL SPEED (factory set) DOT ON LINE

(set 3-5 fpm)

DEFAULT SETTINGS

If valve is received from Maxton, only minor adjustments may be required.

CONTROL BLOCK

DOWN TRANSITION

OUT

(CCW)

to stop.

(faster rate)

DOWN ACCELERATION

OUT

(CCW)

to stop.

(faster rate)

DOWN STOP

OUT

(CCW)

to stop.

(faster rate)

MANUAL LOWERING

(CW)

to stop.

VALVE BODY

DOWN SPEED Turn OUT (CCW) 4 threads above lock nut.

(faster speed)

DOWN LEVEL Turn OUT (CCW) 2 threads above lock nut.

(faster speed)

DOWN SECTION ADJUSTMENTS

(Start with car at upper landing)

adjuster

as required. Send car to upper landing.

*(Read high speed).

Start by turning

adjuster IN (CW) to stop. Register a down call

and turn the

adjuster slowly OUT (CCW) until the car

accelerates smoothly. Send car to upper landing.

*(Accel 0.04g-0.09g).

IN (CW) so that the car slows to

provide 4 to 6 inches of stabilized down leveling. Send car to upper

landing.

* (Decel 0.04g-0.09g).

Disconnect

coil. Register a down call, hold

adjuster in place

and set down level speed at 6 to 9 fpm with the

adjuster.

Tighten both

lock nuts (snug tight). Reconnect

coil.

* (leveling speed 6 to 9 fpm).

Turn

IN (CW), when necessary, for a softer stop.

MANUAL LOWERING: Turn ML screw OUT (CCW) to

lower car downward at leveling speed when necessary.

RELIEF:

Land car in pit and install pressure gauge in

port.

Maximum operating pressure.

Turn

adjuster OUT (CCW) to stop. Turn RELIEF

adjuster OUT (CCW) two turns.

Close the manual shut off valve to the jack.

RELIEF

IN (CW) to increase pressure. Final setting should be

in accordance with local code requirement not to exceed

150% of maximum operating pressure.

Tighten the lock nut (snug tight).

Restart to check the pressure relief setting.

Seal as required.

Open the manual shut off valve to the jack.

Readjust

for proper Up acceleration.

*(Accel 0.04g-0.09g).

BPS

Disconnect the

coil, turn

IN (CW), register an up call and

turn

BPS

IN (CW) until the car just moves. Next, turn the

BPS

adjuster OUT (CCW) until it stops the movement of the car, then

OUT 1/ 2 turn more. Snug lock nut on

BPS

adjuster and stop pump.

Reconnect the

coil.

coils energized, car

should not move), slowly turn

OUT (CCW) to attain

full up speed within 24 to 36 inches.

(Accel 0.04g-0.09g).

Disconnect the U coil. Turn UL adjuster IN (CW) to stop and

3 to 5 fpm. (If not, readjust LS*). Turn UL adjuster OUT (CCW) to

attain 9 to 12 fpm leveling speed. Reconnect the U coil and lower

the car to lowest landing.

*(Read leveling speed).

IN (CW) so that the car slows to

provide 4 to 6 inches of stabilized up leveling. Repeat steps 3 and 4

as necessary.

*(Decel 0.04g-0.09g).

With

adjuster fully OUT (CCW), car should stop 1/4" to 3/8"

below floor. After a normal up run, turn

IN (CW) as needed to

bring car to floor level. The pump must be timed to run ½ second

after the car has reached the floor.

With empty car at bottom floor, disconnect

coils and

BPS

and

LS*

Dot on the

adjuster should be referenced to the line between

F / S. When necessary, disconnect the

coil and

turn the

adjuster IN (CW) to stop. Unlock the LS adjuster by loosening the

screw next to the symbol 1 turn. Move the

adjuster slightly

toward S for slower or F for faster leveling speeds. Set adjustment

from 3 to 5 fpm with the

adjuster, tighten locking screw down,

verify LS speed after tightening screw, then repeat step 3.

* (Level Speed Test 3 to 5 fpm).

ADDITIONAL ADJUSTMENT INFORMATION FOR THE

UC2 / UC2A ON THE BACK SIDE

UP SECTION ADJUSTMENTS

(Start with car at lower landing)

Содержание EMV10







































































































Результаты поиска

Содержание EMV10

Отзывы:

Бренды по названию

Популярные бренды

Maxton EMV10, Руководство пользователя

Результаты поиска

Содержание EMV10

Отзывы:

Бренды по названию

Популярные бренды