6
7
GB
GB
• Locate the arrow on the front of the drill housing.
• Identify the torque settings and 1 drill setting on the torque adjustment collar. • Rotate the torque
adjustment collar to the desired setting, aligning the required number on the torque adjustment collar with
the arrow on the drill housing.
• To increase or decrease torque, rotate the torque adjustment collar. The lower the number, the lower the
torque setting. The higher the number, the higher the torque setting.
Always check that the correct torque is selected by practising on scrap material prior to carrying out a job.
The torque setting required to drive screws will differ with different materials. Start with the torque setting
on the number you think is appropriate and simply increase the torque adjustment collar to a higher
number if the screw head is not sitting flush with your work piece. Remove the screw after adjusting and r
e-drive the screw back into the work piece until the correct torque adjustment leaves the screw head flush
with your work piece.
Keyless Chuck
A keyless chuck is included on your drill to allow for easy installation and removal of bits/accessories. The
chuck is divided into two parts. The rear is called the collar and the front is the body.
To open and close the keyless chuck, grasp and hold the collar of the chuck with one hand and rotate the
chuck body with your other hand.
The arrows on the chuck indicate in which direction to rotate the chuck body in order to GRIP (tighten) or
RELEASE (unlock) the drill bit.
Warning! Do not hold the chuck body with one hand and use power of the drill to tighten or loosen the
chuck jaws. The chuck body could slip and your hand could come in contact with a rotating accessory. This
could cause an accident resulting in personal injury.
Changing the Direction of Rotation
The direction of rotation can be changed with the forward/release selector, this is located above the
variable speed switch.
To select the forward drilling position, push the forward/reverse selector hard left. To select the reverse
drilling position, push the forward/reverse selector hard right
The variable speed switch can be locked off by pushing the forward/reverse selector into the middle of both
the forward and reverse positions.
Do not change the direction of rotation while the keyless chuck is in motion
DRILL OPERATION
The Variable Speed Switch
Turn the drill ON by depressing the variable speed switch
To turn the drill OFF release the variable speed switch
Speed Control
The drill has a 2-speed gearbox, the speed selector(3) is located on the top of the drill. First gear has a
range of 0-350/min, second gear has a range of 0-1100/min. the speed can be varied from 0 to maximum in
switch. This way you can select the best possible speed for the job required
LED Lights
The drill has 1 LED light built into the unit. The LED light is located above the variable speed switch.
The LED light turns on automatically when you depress the variable speed switch.
The LED light illuminates dark areas in tight corners to assist with drilling and screw driving. This helps
achieve a more accurate result in your workpiece.
LED POWER CAPACITY INDICATOR
3 LEDS will show you the capacity of battery.
CHARGING THE BATTERY
The drill has been shipped in a quick charge condition. You should charge it prior to use.
Plug the charger into a power outlet.
Insert the battery into the charger. The recess of the battery terminals will have a firm connection. Upon
proper contact the red and green light will illuminate and when fully charged the red light will go out and
only the green light will be illuminated.
The battery will take one hour to charge. Charging starts automatically . Remove the battery (5) from the
charger after one hour.
When the battery is hot, it may not charge immediately. This is a feature of the lithium ion battery
as charging hot batteries shortens their life. In this case, the green light only will illuminate when the
battery is inserted into the charging. The battery needs to cool which may take several minutes and it will
automatically start charging once cooled.
Initial Charge
Charge your battery for one hour then use it until it runs down and only slowly operates.
Repeat this charge and discharge process approximately 4-5 times, this will ensure that the battery is
performing to its highest capacity.
Charger will not turn off when the battery is fully charged.
Important Charging Notes
The charger and battery may become warm to touch while charging. This is a normal condition, and does
not indicate a problem.
Use the charger at nor mal room temperatures whenever possible. To prevent overheating, do not cover
the charger and do not charge the battery in direct sunlight or near heat sources.
If the battery does not charge properly:
1. Check current at power outlet by plugging in a lamp or other appliance.
2.If charging problems persist, have the complete drill checked by an electrician or a power tool repairer.
Battery
The length of service from each charging cycle will depend on the type of work you are doing. The battery
in this drill have been designed to provide maximum trouble free life. However, like all batteries, they will
eventually wear out.
To obtain the longest possible battery life, we suggest the following: Store and charge your battery in a cool
area. Temperatures above or below normal room temperature will shorten battery life.
Never store batteries in a discharged condition. Recharge them immediately after they are discharged. All
batteries gradually lose their charge. The higher the temperature the quicker they lose their charge. If you
store your drill for long periods of time without using it, recharge the batteries every month or two. This
practice will prolong battery life.
CLEANING AND MAINTANCE
When not in use, the drill should be stored in a dry, frost free location, out of reach of children. Keep
ventilation slots of the drill clean at all times and prevent any foreign matter from entering. If the housing
of the drill requires cleaning, do not use solvents but a moist soft cloth only. Blow out the ventilation slots
with compressed air periodically.
ENVIRONMENT
Do not dispose of electric tools, accessories and packaging together with household waste material
- in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compatible recycling facility.
TROUBLE SHOOTING
Fault Symptom
Possible Cause
Troubleshooting
Out of service
IInsufficient charging capacity in
accumulator
Replace fully recharged
accumulator
Accumulator damage
Replace accumulator
Motor wearout
Replace electric motor by
repairer
Switchboard damage
Replace switchboard by repairer
Insufficient running
Insufficient charging capacity
Replace fully recharged
accumulator
Damage in gear wheel
Replace gear wheel by repairer
Motor wearout
Replace electric motor by
repairer