background image

 

 

vents;  must  be  equipped  with  the  proper  electrical  and  hydro  systems,  built  in  accordance  with  the 
standards related to facilities and workplace safety in the country of installation. 
The maximum working height, referring to the highest surface level, must be 1.6 metres from the floor. 

After installing the appliance, if required, apply the suitable adhesive symbol 

(supplied) at a height of 

1.6  metres.  To  favour  air  circulation  around  the  appliance,  leave  a  space  of  about  10  cm  between  the 
appliance sides and the surrounding walls (or other appliance), and between the back and the back wall 
(see the attached “Technical Data Sheet”). The appliance must be positioned so that the rear wall is easily 
accessible to set up various electrical connections and to carry out any possible maintenance. Do not install 
the appliance near any equipment that may reach high temperature values (e.g. deep fryers).  
Should the appliance be installed near walls, shelves, counters and the like, these must be non-flammable 
or heat-resistant; otherwise, they must be protected by adequate fire retardant coating. Accordingly, it is 
indispensable to act in compliance with the fire prevention regulations in force.  
Cooking  produces  hot  smoke/vapour  and  odours  which  are  extracted  through  the  suitable  vent  device 

located  at  the  top  of  the  appliance  and  marked  with  the  symbol 

.It  is  recommended  to  place  the 

appliance  under  an  extraction  hood  or  to  use  the  suitable  condensation  hoods  in  order  to  convey  the 
smoke/vapour to the outside.

 

 
Warnings 

 

Make sure there are no objects and/or materials obstructing the oven’s exhaust device. 
 
The hot smoke/vapour produced during cooking must run freely out of the exhaust device in order not to 
compromise the regular operation of the oven. 
 
Inflammable materials must not be left near the oven’s exhaust device. 

2.6.1 Table top oven placement  

The appliance must be placed in a perfectly horizontal position on a table or similar support; never on the 
floor. To facilitate oven levelling, the feet are adjustable in height. 
For  safety  reasons  it  is  recommended  to  use  the  specific  table  produced;  otherwise  the  dimensions  and 
weight of the appliance must be taken into account.  
The appliance is unsuitable for recessed installation and cannot work without the 4 supporting feet. 
 
Warning 

 

If  the  appliance  is  positioned  on  a  wheeled  table/support,  ensure  that  the intended  movement  does  not 
damage electrical wires, water pipes, drain pipes or anything else. 

2.7 Electrical connection 

The appliance’s connection to the electric power network and the connection systems must comply with 
the applicable regulations in the country of installation. Before setting up the electrical connection ensure 
that: 
 
the  voltage  and  frequency  of  the  power  supply  system  match  the  specifications  of  the  "technical  data" 
plate affixed to the side of the appliance; 
 
the power supply system is able to withstand the appliance's load (see "technical data" plate); 

 

the  power  supply  system  is  fitted  with  an  effective  earthing  connection  according  to  the  regulations  in 
force; 

 

in  the  permanent  connection  to  the  electric  power  network,  a  protective  pole  switch  must  be  placed 
between the appliance and the mains (e.g. circuit breaker) with minimum opening between the contacts of 
overvoltage category III (4000V) and a differential switch, sized for the load and complying with applicable 
regulations. 

 

the protective pole switch used for the connection is easily accessible when the appliance is installed; 

 

the yellow/green earthing cable is not interrupted by the switch; 
 

Содержание 08560210















Отзывы: