MaxFlight MT3000 ELECTRIC Скачать руководство пользователя страница 49

Страница: 49 / 213

iv. Heat motor half of coupling to 350 degrees on bearing heater.

WARNING

Use gloves to protect hands from severe burns when

handling hot metal couplings. The following step must be
performed quickly and accurately or the coupling will not be able
to be moved once cooled.

v. After couplings are heated using gloves, immediately position

over key and motor shaft match ends of the shaft to face of
coupling.

vi. Repeat steps four and five for the main drive shaft end.

vii. Pre-lube the Sleeve and couplings with bearing grease.

viii. Slightly lube seal flanges.

ix. Place sleeve over motor coupling, insert the seal far enough to

allow the retaining ring groove be visible.

x. Install the retaining ring in a spiral manner.

xi. Repeat steps 7-10 for main drive shaft side.

xii. Position motor to rear of right A frame.

xiii. Locate 3/8 inch bolts (2) flat and lock washers, nuts.

xiv. Feed bolt through bottom two extreme mount holes on motor

frame, place three flat washers over each bolt to act as spacers.

xv. Lift motor and position bolts through A frame mount holes,

place tapered washer over bolt, lock washer and nut, finger
tighten only. Release the lift brake, knob at rear CW till it
locks.

xvi. Remove the coupling sleeve grease fitting bolt. (Center of

Sleeve)

xvii. Insert a ¼ inch allen wrench till it bottoms out.

xviii. Position lift encoder over drive shaft with locking collar facing

gear box.

xix. Position main drive shaft near and in line with input shaft of

gear box, align keyways and key, slide the solid coupling onto
the main drive shaft till it bottoms on shaft. Tighten set screws.

xx. Position the long 3/8 inch bolt on end top mount plate hole,

attach two 3/8 nuts over bolt, swing motor up and feed bolt
through upper mount hole on A frame. Attach 3/8 lock washer
and nut. Do not tighten now.

xxi. Measure distance from side of shaft to main base at both ends

of the drive shaft, the distance must be equal. See DET-

xxii. Adjust and then tighten the top motor mount bolt when

distances are correct.

xxiii. Remove ¼ allen wrench from coupling sleeve and reinsert the

grease plug. This procedure assures that the proper distance is
set between main and motor shafts so that they do not bottom
out during operations.

Содержание MT3000 ELECTRIC






















































































































































































































Результаты поиска

Содержание MT3000 ELECTRIC

Отзывы:

Бренды по названию

Популярные бренды

MaxFlight MT3000 ELECTRIC, Руководство пользователя

Результаты поиска

Содержание MT3000 ELECTRIC

Отзывы:

Бренды по названию

Популярные бренды