Maxey Moverley VCL orbiter gold Скачать руководство пользователя

Страница: 6 / 9

Maxey Moverley Limited, 6 Broad Ground Road, Lakeside, Redditch, Worcestershire, B98 8YP

Web: www.cctvrepairs.com ● Email: [email protected]

Tel: 01527 522299 ● Fax: 01527 522588

Issue 1.1

| Page 6

Quick Reference Guide

VCL Orbiter Gold/Lite

LED D17 will illuminate if the receiver that is being controlled by Coax telemetry is selected by the

transmitter and the coax telemetry is satisfactory. If the receiver is being controlled by twisted pair

telemetry, LED D17 will flash whenever a valid telemetry command is received.

VR1 (LIFT) and VR2 (GAIN) are factory set. They are designed to improve the picture quality

transmitted by the Orbiter Gold/Lite when long cable runs are involved and a degradation of picture

quality occurs. Before adjusting either the LIFT or GAIN, ensure that the iris is correctly adjusted.

If the image is ‘smearing’ due to a long cable run, then the LIFT pot may be adjusted to sharpen the

image. If the contrast of the image is low, (caused by an attenuated video signal), make adjustments

by turning the GAIN pot.

Note.

Over adjustments of either the GAIN or the LIFT pot will result in further image quality

degradation.

Address Settings

The addresses for each Orbiter Gold/Lite are set as shown in the table below. Set the poles on

DILSW2 to the desired position for each address.

Figure 9.

Address Settings

Содержание VCL orbiter gold









